Question about 2008 Honda Civic

Open Question

Where is the purge valve located on a 2008 Honda Accord?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 77 Answers

SOURCE: where is the purge valve located on a 2004 honda LX?

It is with a 2 wire Black connect located next to the throttle body. Locate the green cap on the evap hose and follow it to the throttle body and that is the purge valve.

Posted on May 17, 2009

Molson02536
  • 3854 Answers

SOURCE: location of a pcv valve on a 2005 honda accord

You have to remove the "ignition cover", ie. the plastic cover that says 3.0L, you will see a hose coming from the passenger front corner of the intake manifold, that is one of the two PCV hoses, the other one is on the rear driver corner of the intake manifold.

Follow the first hose downwards and you will find the PCV valve just below some other tubings, it sits fore/aft, i.e. lengthwise to the car. I hope this helps good luck

Posted on Apr 08, 2009

  • 88 Answers

SOURCE: Location of Honda Accord Canister purge solenoid

on canister close to gas tank

Posted on Sep 16, 2009

  • 105 Answers

SOURCE: 2008 honda accord replace rear brakes

no, 12mm wrench or ratchet on 12mm socket. the piston is tough to push back in. its a twist in type and you will need some force to push and twist the piston back in. - note rear brake pads wearing out on the new 08-09 accords are very common and if under 16-18 thousand miles it may be covered. honda knows about this problem

Posted on Oct 27, 2009

philschneide
  • 448 Answers

SOURCE: where is the pcv valve located on a 1999 honda

Under hood, center, upper engine area, top of engine, MOUNTED IN THE VALVE COVER (probably has a rubber hose connected to it, coming from a place further back toward the firewall) It usually is removed by simply pressuring it upward out of the rubber gromet that it resides in.
Hope this lets you find it.

Posted on Oct 27, 2009

Testimonial: "u guys are great! I'll be back with more stuff. hopefully one day I can be among you answering these questions! thanks a million!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Honda Civic purge valve location?


Upper most writing is location.
26350908-1dkniz51vt3y0ck424ohao12-5-0.jpg

Nov 11, 2016 | 2008 Honda Civic

1 Answer

Find and replace canister purge valve for 2002 honda accord


This code P1456 does mean that you replace purge valve . Could be other thing's must test the Evaporative emission system . P1456 Honda Evaporative Emissions Control System Leakage Fuel Tank Suggest you take an have a qualified repair shop diagnose the problem .

Oct 08, 2016 | 2002 Honda Accord

1 Answer

Honda Accord 2008 whistle in room


Wait until engine is cool. Check coolant level.

Air pocket is form in the coolant system.

Put car on top of an oil change ramp and slowly add coolant.

It will take 30 to 45 minutes to purge air pocket,

Jan 15, 2014 | Honda Cars & Trucks

1 Answer

Where is the evap canister solinoid located at honda accord 2000


2000
why not post the DTC error for better answers/?
and country.?
now my answer from USA, cars.
1: in usa open hood, see vacuum sticker, its there.
2: in FSM there are 3, purge control and bypass VSV. and vent shut off VSV.
so which one. ill answer for all 3.
at the canister. (im looking ,in alldata.com so an you)
1: CAN , hose.
one goes to tank, directly not that hose.
2: hose 2. is vent shut valve top of CAN, and goes to Vent can filter.
3: hose 3: to purge joint then purge valve.
4: and last host to bypass valve. this valve has 3 hoses (unique)

alldata.com click evap emmissions tab.

Oct 25, 2013 | 1998 Honda Accord

2 Answers

Check engine light is on, code 1457, I replaced the gas cap...still won't go away?


This is a common problem with these and a few other Honda cars.

The code means "Evap Bypass Solenoid Valve Failure"

The solution is to replace a few parts dealing with the EVAP system.

You can call your local Honda dealer, as there is a TSB (technical service bulletin) on this problem, and it may be covered under warranty.

The TSB number to give them is 03-001.

Mar 19, 2010 | 1999 Honda Accord

1 Answer

CHECK ENGINE LIGHT CAME ON WITH CODE 1259. AUTOZONE SAID ITS PURGE VALVE SOLENOID. WHERE IS THAT LOCATED?


is a vtec solenoid valve. it located on your left behind the valve cover . vtec solenoid looks like a round cap. anyway do you have a oil leaks in your car?









Jul 27, 2009 | 1998 Honda Accord

Not finding what you are looking for?
2008 Honda Civic Logo

Related Topics:

869 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...