Question about Cars & Trucks

Open Question

How do I replace the Swirl Control Valve on a 2002 Infininty I35

Received the DTC P1800 and the dealer said to start with the Control Solenoid. However, I am having trouble identifiing the part.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Swirl Valve

I have been working on a 96 nissan truck for three years for an evap code and swirl control , I finally just made sure the swirl control solenoid operated properly then disconnected the vacuum hose from the swirl control actuator and plugged it . code fixed.been driving 3 months, no code

Posted on Nov 15, 2008

  • 312 Answers

SOURCE: Pls where is Swirl Control Solenoid Valve located in Infiniti QX4

This link shows the location of the SCV, If your motor is different the location should be similiar. http://img510.imageshack.us/img510/5687/vacuumdiagramuh3.jpg

There's a vaccuum line that runs off the SCV to the SCV check switch.

P0442: Have you inspected the lines, charcoal cannister etc? Make sure the fuel cap is tight. The easiest way to check the system is to have someone perform a smoke test. I had a DTC on my car which indicated a EVAP problem, it turned out to be the Fuel tank evaporator Control Solenoid.

Posted on Sep 22, 2009

  • 53 Answers

SOURCE: 4L80E WITH DTC PO757A 2-3 SHIFT SOLENOID VALVE

it turned out to be the stall in the converter. i needed to install a low stall and the code never came back.

Posted on Mar 16, 2010

Testimonial: "this helped"

  • 613 Answers

SOURCE: PO1130 swirl control valve? I have a 1997 nissan P

it is a sensor on the back of the intake manifold

Posted on Sep 24, 2010

ZJLimited
  • 17970 Answers

SOURCE: 2002 nissan maxima, check engine

About DTC P1800, I suggest check the harness and verify it is plugged in and still functioning. Also, try checking your vac tubes to verify that they are not reversed. Also read this TSB with details about correct diagnostic: DTC P1800 VIAS CONTROL SOLENOID VALVE

The VIAS control solenoid valve cuts the intake manifold vacuum signal for power valve control. It responds to ON/OFF signals from the ECM. When the solenoid is off, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and feeds the vacuum signal to the power valve actuator.

DTC detecting condition:
• An excessively low or high voltage signal is sent to ECM through the valve
Possible cause:
• Harness or connectors (The solenoid valve circuit is open or shorted.)
• VIAS control solenoid valve

Will need replaced the solenoid valve (P/N - 149558J10A). The valve is located under the engine cover. It's a Nissan only part so you have to order from the dealer, either online or in person. It's cheaper online. Check this sample Nissan engine location (click image for zoom)...

zjlimited_1658.jpg



DTC P1147 - Bank1 Sensor 2 O2 sensor maximum voltage monitoring
Component Description: The heated oxygen sensor 2, after three way catalyst, monitors the oxygen level in the exhaust gas on each bank.

Even if switching characteristics of the heated oxygen sensor 1 are shifted, the air fuel ratio is controlled to stoichiometric, by the signal from the heated oxygen sensor 2.

This sensor is made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. Under normal conditions the heated oxygen sensor 2 is not used for engine control operation.

DTC detecting condition: The maximum voltage from the sensor is not reached to the specified voltage.

Possible cause:
Harness or connectors (The sensor circuit is open or shorted)
Heated oxygen sensor 2
Fuel pressure
Injectors

Majority of cases this is either a faulty O2 sensor, or short/open in wiring harness. Bank1 sensor2 is the rear O2 sensor on the passenger (right) hand side (click image for zoom):

zjlimited_50.png

Here is simple test with voltmeter to test O2 sensor. If it fails test, replace sensor. If not, then you will have to start tracing the wiring harness for a short/open in it (click for zoom):

zjlimited_51.png

And here additional details: DTC P1147 O2 Sensor

Keep us updated.

Posted on Aug 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 nissan maxima oem trouble code p1800


Variable Intake Air System Control Solenoid Valve Circuit

Read more: https://www.autocodes.com/p1800.html

Mar 02, 2017 | Nissan Maxima Cars & Trucks

1 Answer

Where is the purge control valve located on 1998 nissian pathfinder


Location should be back by the fuel tank.

first off, the P1447 DTC is triggered when the EVAP control system isn't operating properly or there is a leak between the intake manifold and the pressure sensor. the parts between the pressure sensor and intake manifold are:

1. EVAP canister purge control solenoid valve
2. EVAP canister purge control valve
3. EVAP canister purge volume control valve (Part # 14930-3M201) YOU WILL HAVE TO DOUBLE CHECK ON THE PART NUMBER WITH THE DEALER FOR THE PRICE.

If you've received this P1447 DTC, chances are that the brick of charcoal in the canister has fallen apart over time, and filled the lines with charcoal. this affects parts 2 & 3 from the above list, and of course the EVAP canister (Part # 14950-1s717 $144.22). but when you replace the canister, you have to replace the EVAP canister vent control valve (part # 14935-54u06 about $100), and don't forget the o-ring (part # 16618-40u00 about $1.60) that goes between the canister and the vent control valve.

If you attack this DTC early enough, all you have to replace is the canister and vent control valve with the o-ring, which will add up to under $300 MSRP...a lot better than paying upwards of $1000 for parts and labor. Don't be scared to do it, it's actually quite simple.

D

Sep 28, 2015 | Cars & Trucks

1 Answer

DCT P1800


code P1800 VIAS control solenoid valve circuit.

Jul 02, 2013 | 2004 Nissan Murano SL

1 Answer

2002 altima codes 1212 and 0011 please help


DTC P1212 - Mass Air Flow Circuit Intermittent Low
DTC P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

A P0011 DTC trouble code may be caused by one or more of the following:

  • Incorrect camshaft timing
  • Wiring problems (harness/wiring) in intake timing control valve control solenoid system
  • Continuous oil flow to VCT piston chamber
  • Failed timing valve control solenoid (stuck open)

Possible Solutions

This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 21, 2012 | 2002 Nissan Altima

1 Answer

Engine code P1800 for infiniti I35, how do I fix this?


Code 1800 is for the Variable Intake Air System control solenoid.

The VIAS control solenoid valve cuts the intake manifold vacuum signal for power valve control. It responds to ON/OFF signals from the ECM. When the solenoid is off, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and feeds the vacuum signal to the power valve actuator. An excessively low or high voltage signal is sent to ECM through the valve
Read more: http://engine-codes.com/p1800_infiniti.html#ixzz20dCff9ht

Jul 13, 2012 | Cars & Trucks

2 Answers

Enciendo el auto y me encinde la luz de check y dice que es el codigo p1130


DTC P1130 - Swirl Control Valve Control Solenoid Valve

Otros detalles acerca de los codigos de falla los puede encontrar en este enlace: manual_detalle.php?manual_id=101

Buena suerte.

May 26, 2011 | 1996 Nissan Pickup

1 Answer

Check engine light on code p1800 amd p650 is it


CODE PO1800 VIAS CONTROL SOLENOID VALVE CIRCUIT. I DID NOT SEE CODE PO650 BUT CODE PO1800 IS A FAULTY VIAS CONTROL SOLENOID VALVE.

Apr 23, 2010 | 2002 Nissan Altima

3 Answers

Hi i have 02 altima 3.5 v6 who have check engine light with code p1800 what is manufactured transmission control can anyone help me what that means?


You may want to have someone else take a look at it. The Nissan P1800 trouble code is not a transmission control problem. It is described as follows:

Trouble diagnosis name: VIAS control solenoid valve circuit.
Component Description:
The VIAS control solenoid valve cuts the intake manifold vacuum signal for power valve control. It responds to ON/OFF signals from the ECM. When the solenoid is off, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and feeds the vacuum signal to the power valve actuator.
DTC detecting condition:
•An excessively low or high voltage signal is sent to ECM through the valve.
Possible cause:
•Harness or connectors (The solenoid valve circuit is open or shorted.)
•VIAS control solenoid valve

Check your vacuum hoses to make sure they are in good shape and are securely attached Aslo check the wiring harness is ok and securely attached as well. If they are, you’ll probably need to replace your VIAS. It's right next to the throttle body.

Jan 25, 2010 | 2002 Nissan Altima

2 Answers

Pls where is Swirl Control Solenoid Valve located in Infiniti QX4


This link shows the location of the SCV, If your motor is different the location should be similiar. http://img510.imageshack.us/img510/5687/vacuumdiagramuh3.jpg

There's a vaccuum line that runs off the SCV to the SCV check switch.

P0442: Have you inspected the lines, charcoal cannister etc? Make sure the fuel cap is tight. The easiest way to check the system is to have someone perform a smoke test. I had a DTC on my car which indicated a EVAP problem, it turned out to be the Fuel tank evaporator Control Solenoid.

Sep 22, 2009 | Infiniti QX4 Cars & Trucks

1 Answer

Swirl Valve


I have been working on a 96 nissan truck for three years for an evap code and swirl control , I finally just made sure the swirl control solenoid operated properly then disconnected the vacuum hose from the swirl control actuator and plugged it . code fixed.been driving 3 months, no code

Aug 07, 2008 | 1996 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...