Question about 2000 Honda Civic

Open Question

Key out of ignition, but chime does not recognize so key fob doesn't work

When key is removed from ignition, chime still on. Key fob will not operate because it still thinks key is in ignition

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

toneman2121
  • 775 Answers

SOURCE: I just change the key ignition switch but my new

take it to the dealer

Posted on Feb 25, 2010

  • 14036 Answers

SOURCE: Can't remove key from ignition for '00 honda accord @ park positi

push key in turn on and off push key in work switch off and on .if dont release you probably going to have to take out the ignition switch. make sure your car is all the way in park.

Posted on Apr 07, 2009

  • 5 Answers

SOURCE: KEY WONT TURN IGNITION

Your car uses a transonder key, a key with a small chip embedded inside. The transponder is matched to the immobilizer unit in your car. When the key is inserted into the ignition, the immobilizer searches for that transponder, if it's not near the ignition, the car will just keep turning over and not start. Your only real options are to replace the steering lock or buy a transponder bypass unit, which I do not recommend. Just do a google search.

Posted on Sep 03, 2009

  • 205 Answers

SOURCE: honda ridgeline key fob program

If it is a factory keyless system than you do need it done by the dealer, but if it is an after market system then reply back with manufacture and model.

Posted on Oct 17, 2009

  • 41 Answers

SOURCE: the lock button on my key fobs will not lock the doors on 06 honda crv

CHeck to see if it is the right battery - Should be a CR1616 - previous year models, had a different battery.

Does the light come on on the key fob, when you push the button?

You may have to reprogram the remote - check the owners manual for instructions - if you can't find them...

Programming the Transmitter
NOTES:
• The system accepts up to three transmitters. The
transmitter codes are stored in a stacking-type
memory. If a fourth transmitter code is programmed,
the code for the first transmitter is erased.
• Entering the programming mode cancels all learned
transmitter codes, so none of the previously
programmed transmitters will work. You must
reprogram all of the transmitters once you are in the
programming mode.
• You must complete each step within 4 seconds of
the previous step to keep the system from exiting the
programming mode. Program the transmitters within
10 seconds.

1. Turn the ignition switch to ON (II).
2. Press the "Lock" or "Unlock" button on one of the
transmitters. (An unprogrammed transmitter can be
used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the
same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the "Lock" or "Unlock" button on the same
transmitter. Make sure the power door locks cycle
to confirm that the system is in programming mode.
7. Within 10 seconds, press the "Lock" or "Unlock"
button on each transmitter. Make sure the power
door locks cycle after you press each transmitter
button to confirm that the system accepted the transmitter's code.
8. Turn the ignition switch to LOCK (0) to exit programming mode.


IF so, and more likely, the fuse on the car side of the remote, is probably gone.

Posted on Apr 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reprogram a key fob


IMPORTANT: Before entering programming mode, have in possession all of the remotes you
will be useing on the vehicle. Once you program the remote. all previous remotes that were
programmed will be erased from memory. The other remotes will not be functional until you
program the them again.
1. Remove the key from the ignition.
2. Close all doors.
3. Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or
owner's manual to properly locate the "MALL PGM" fuse.
4. Insert the key into the ignition, and turn to the ACC position.
5. Turn the key to OFF and then back to ACC within 1 second.
6. Open and close any vehicle door. A chime will be heard when the system enters into
programming mode.
7. Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds.
IMPORTANT: After 7 seconds, a chime may be heard confirming successful
synchronization. It is necessary to wait approximately 14 seconds for a second chime
that will confirm successful programming.
8. Repeat step 7 now for each additional remotes to be programmed including any existing
remotes.
9. Remove key from ignition.
10. Install the "MALL PGM" fuse back into the fuse panel and test remote(s).

Sep 10, 2012 | 1999 Pontiac Grand Prix

2 Answers

KEY FOB


Hi there:
From Owners Manual...
7_2_2012_3_58_16_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 02, 2012 | 2008 Dodge Ram 1500 2WD

2 Answers

08 dodge ram key FOB reprogramming


ATTENTION: You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.

Click here to find a Locksmith in your area to program this remote.
1. Enter your vehicle and close all doors.

2. Fasten your seat belt ( fastening the seat belt will cancel any chiming that may
confuse you during this programming procedure.)

3. Place key into the ignition.

4. Turn the ignition to the ON position ( DO NOT START THE ENGINE )

5. Press and hold the UNLOCK button on a working remote.


6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than
10 seconds, then press and hold PANIC button.

7. When a single chime is heard, release both buttons. The chime indicates the system
is in program mode.

8. Press and release both the LOCK and UNLOCK buttons, simultaneoulsly on the remote
to be programmed.


9. A single chime will be heard. The chime indicates the the remote was recognized.


10. Within 4 seconds of hearing the chime, press and release any button on the remote
being programmed.

11. A single chime will be heard The chime indicates the remote has been programmed.

12. Repeat steps 8 to 11 for a total of 4 remotes.

13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.

Jul 02, 2012 | 2001 Mercedes-Benz C-Class

1 Answer

98 intrigue keyless entry


Here's what i found.

1. Close all doors.

2. Insert key into the ignition cylinder but do not turn it.

3. Press and hold the Unlock button on door lock switch on drivers door.
Hold until instructed to release in step 6.

4. Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.

5. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.

6. Release door lock switch on drivers door panel.
A Chime will sound 3 times indicating that you are in programming mode.

7. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
A chime will sound 2 times if remote has programmed successful.

8. Repeat step 7 if you are programming additional remotes.

9. Remove key from ignition to exit programming mode.

NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.

Did you make sure to pull the key out after the procedure? This closes the "programming mode".

Mar 14, 2012 | 1998 Oldsmobile Intrigue

1 Answer

How can I reprogram my Jaguar X Type Key so I can unlock and lock my doors?


if your just programming the fob to the module and it has not been replaced and your just needing a manual reset,then follow the folowing procedure:

1 Insert key into ignition
2 Turn key to 'I"
3 Turn key "II" and back to 'I' quickly 4 times
4 Alarm system will chime once when key is back to 'I' for the
fourth time
5 Remove key from ignition
6 Press any button on each key fob and alarm system will chime
for each fob if it has been programmed correctly
7 Press unlock/lock/trunk etc to make sure everything works

Dec 12, 2011 | 2003 Jaguar X-Type

1 Answer

Key fob not working i have changed the battery


hi.

the fob probably needs to be rematched to the car again.
EASY>>>>>



Reprogramming an X-Type Key Fob.

Step 1
Open the
driver side door.
Step 2
Turn the ignition switch to the
'auxiliary' position, then turn the ignition switch to the 'ON' position and
back to the 'auxiliary' position four times. *This must be done fairly quickly.
If you have done it correctly, you will hear a chime come from the
GEM*
Step 3
Turn the ignition switch to 'OFF' position.
Step
4

Remove the key from the ignition.
Step 5
To program the
transmitter, press any key within ten seconds. **If it worked, you should hear
another chime come from the GEM**
Step 6
Close the door...YOU'RE
DONE!
I have done this on my dads x type. it does work. do not forget to have the drivers door open like i did.

Jun 09, 2011 | 2004 Jaguar X-Type

1 Answer

Key fobs do not lock/unlock doors, horn or trunk release. Batteries in key fob is good, fuses are good. What's next/


Retrain the fobs following the procedure in your owner's manual:

 Once entering this procedure, programming the first transmitter erases all previous transmitters. You must program all transmitters.
 Program one vehicle at a time. One transmitter could be programmed into other vehicles that are also on
program mode in close proximity.
1. Sit in the driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all vehicle doors.
4. Press and hold unlock on the door lock switch.
5. While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do
not rotate the ignition lock cylinder.
6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain
in the LOCK position for the rest of the procedure.
7. Release the door lock switch. You will hear three chimes. This chime feedback indicates that transmitter
programming is active.
8. Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for 12
seconds.
You will hear two chimes. This chime feedback indicates that the transmitter has been
programmed successfully.
9. Repeat step 8 for the rest of the transmitters (for a total of 4 transmitters).
10. Exit this procedure by removing the ignition key from the ignition lock cylinder.

Feb 12, 2010 | 1999 Oldsmobile Intrigue

2 Answers

Key fob not working after battery change ford focus 2006


Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

May 28, 2009 | 2006 Ford Focus

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

2 Answers

Central locking


To re programme your key if your fob has three buttons is as follows. Turn the ignition key in quick succession from off to ignition on 4 times. You should hear a chime to indicate programme mode. Quickly remove the key and press the lock button followed by the unlock button. Wait until you hear the chime again and see if the fob works. If it does not operate the central locking, see if you can open the tailgate with the fob, I guess you have a three button remote? If it doesn't, repeat the above but quicker!! it should programme quite easily. When you checked the fuse, did you take it out? I suggest you remove the fuse and wait 30 seconds and put back in, get someone in the car to see if any doors respond to you replaceing the fuse. recheck the fob operation and the key, this maybe the answer.

May 31, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2000 Honda Civic Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...