Question about 2005 Pontiac Montana SV6

Open Question

08 montana sv6 air bag removal

How to remove drivers airbag

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: real right turn signal light - Pontiac Montana SV6 2005

If the 2005 Montana is similar to the 2001 Montana, I have a solution. First you'll need a hexagonal wrench (the 6-sided L-shaped wrench). The tail light assembly is held on by two screws. You'll need the hexagonal wrench to remove them, because a normal screwdriver won't do it. I also had to use a conventional adjustable wrench to get the leverage to turn the hexagonal wrench, because the screws were in there pretty tight. Once you remove the two screws, the whole tail light assembly should come off. Mine required a little force and I had to play with it a bit, but it came off without a lot of work. There will be one set of wires that connects the tail light assembly to the rest of the minivan--try not to damage that set of wires. Once you get the tail light assembly off, you'll have to take apart the assembly that actually holds the lights. No tools should be required. It's held on by four plastic catches. Just undo the catches (easier said than done, but still not too tough) and it comes apart. Then you can pop out the old light and pop in the new light. Then re-assemble. For me, it went back together much easier than it came apart.

Posted on Jan 03, 2009

  • 56 Answers

SOURCE: L.F. heated seat does not work 2005 Pontiac Montana SV6

element in the seat is burned out remove the cover and you will see a burn spot in the element

Posted on Feb 13, 2009

  • 7 Answers

SOURCE: 2005 Pontiac SV6 Montana key fob unlocks doors but will not lock

For the sliding doors you need to clean the contacts, there are 6 or 8 on both sides, just wipe them clean as they are probably covered in oil/grease/grime.

Posted on Feb 14, 2009

  • 1 Answer

SOURCE: Where is the cabin air filter on my 05 montana?

In the Glove compartment on the left hand side there is a black snap on cover pull it from the bottom and it will come open. There is 2 filters in this spot.

Posted on Jun 28, 2009

pippall
  • 1486 Answers

SOURCE: Air bag Light Stuck On 98 Pontiac Montana

Under the front seats you have wires going to your seat belt anchors.These wires are atached to a sensor witch activate the air bags if the anchors have force pull on them.The wires have plugs under the seat.Disconnect the plugs and spray with electical cleaner and replace.Make sure the ignition is switched off befor you attemt doing.90%of the time this will work.good luck.

Posted on Jul 18, 2009

Testimonial: "Excellent help! Thanks so much. Worked like a charm"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dvd player for movies is not working has no power


Possible problems with DVD player after replacing Cabin Air Filter ...

www.topix.com > Pontiac Montana
Apr 13, 2011 - 2006 Montana. Posted in the Pontiac Montana Forum. Leave a Comment ... I recently had my cabin air filter replaced by Jiffy Lube. After they had ... If not, could the dvd player simply blown a fuse and just needs replacing? It just seems ... 14 Famous Movie One-Liners You've Been Quoting Wrong For Years. DVD Repair
Jan 18, 2010
Replace VCR with DVD player in 2001 Montana
Feb 2, 2009
Chevy Uplander "CD Mech Error"
Aug 29, 2008
Reports: 2004-2006 Chevy Uplander Sliding Door Problems ...
Aug 21, 2007
More results from www.topix.com

Pontiac montana sv6 dvd player removal - YouTube

? 1:18
https://www.youtube.com/watch?v=21TTD0ayThc
Oct 15, 2015 - Uploaded by Joshua Freeman
I recently got this 2005 montana sv6 from my grandoa and thedvd player was jamming up and not working ...Missing: movies

Jan 16, 2016 | 2006 Pontiac Montana SV6

1 Answer

Removing a defective blend door on the pontiac montana sv6 2005


removing the heater a c box from under the dashboard

Sep 20, 2014 | Cars & Trucks

1 Answer

Remove airbag on drivers seat


you have to remove your drivers seat, get a knife, very kind remove a fittings of your airbag, then go to your dealer buy a brand new airbag, get a niddle fit it all, and make all the procedure with airbag replacement. thats all

May 07, 2014 | 2007 Skoda Superb 2.0

1 Answer

Airbag deploy


To deploy an airbag you have to put the vehicle into high g manouver like a collision. And after that the vehicle is damaged. Why do you want to deploy the airbag? You can remove it as a single unit, but the vehicle airbag warning light will then stay on all the time. Why would you want to remove it?

Dec 20, 2013 | 2005 Pontiac Montana SV6

1 Answer

2011 golf tdi airbag removal


Driver side you just slide a screwdriver behind the steering wheel. Passenger side you need to remove glove box to access the unit above it. NOTE: Always disconnect power from the battery before tampering airbag unit and have the radio code ready when connecting power from the battery since it will lock up for anti-theft protection.

Nov 29, 2013 | Volkswagen Jetta Cars & Trucks

1 Answer

Hi, I have an 08 Pontiac Montana SV6, when I come


shakes and stalls indicates an engine problem-take it to autozone advanced auto or pepboys and have them check your onboard cpu for fault codes-cheers Denny

Nov 02, 2013 | 2005 Pontiac Montana SV6

1 Answer

2001 pontiac grand am air bag module reset


Yes!!! You can replace it yourself.(Dont let others fool you into paying extra or telling you otherwise.)
-This is for pontiac grand ams 1999-2005 only.
-There are no frontal airbag impact sensors nor are there belt tensioners.
-The SRS system consists of only the (driver airbag) ,(passanger airbag),and the (airbag control module) in 1999-2005 grand ams.

If you crash/wrecked and airbags deployed you will need.
-Driver and Passanger airbags
-Airbag control module

You can buy cheap airbags from a local junkyard any year from 1999-2005 will fit.
You can also find an airbag control module for cheap at your local junk yard BUT YOU MUST FIND ONE WITH THE SAME (PART NO.) AND (SERV NO.) AS THE ONE YOUR REPLACING.The (part no.) and (serv no.) should be at top left of airbag control module.However it does (Not) have to match numbers under barcode or the numbers at the far bottom right of airbag control module.

After you get both airbags and airbag module
-Disconnect car Battery
-Replace airbags
-Replace airbag module (under passanger seat)
-Double check all connections and connect battery.

Congradulations!Your airbags should be back online.

Notes: Two torx 35 head screws hold the driver airbag, access is through two holes behind steering column.
To remove passanger airbag you have to remove glovebox it uses (7mm)screws.After you remove you will see a pair of (10mm)screws holding airbag.
To remove airbag control module First remove passanger seat 2(15mm).Then after removing you will notice a raises area kinda like a vertical bump.Take a razor blade to your carpet and cut it to explose the module underneath.
The airbag module is held by three screws depending on the year of your car it varies.Most likely 3 (10mm).

Mar 24, 2013 | Pontiac Grand Am Cars & Trucks

2 Answers

Was wrecked need to know how to take out the airbag and replace


This process would very depending on each car. Check the fuse box for the airbag fuse. Have it removed before disassembling the airbag assembly. For the driver side airbag... remove the cover of the driver's wheel to gain acces to the assembly. In some cases you will have to remove the cover of the steering columns. For the passenger side airbag you need to remove the dashboard to gain access to the assembly.

Jan 27, 2012 | Cars & Trucks

1 Answer

How to remove the air bag on drivers side to get under the dash


  1. Open hood, disconnect and isolate the battery negative cable.
  2. Wait two minutes for the system reserve capacitor to discharge before beginning any system or component service.

118351360 Instrument Panel Trim - Remove/Install

  1. Remove the steering column opening cover two retaining screws and unsnap cover from instrument panel.

118351361 Knee Blocker Airbag - Remove/Install

  1. Remove four knee blocker airbag retaining bolts from airbag.
  2. Pull down knee blocker airbag and disconnect the one electrical connector.
  3. Remove knee blocker airbag from vehicle. Here

Jan 05, 2012 | 2004 Chrysler Pacifica

1 Answer

I want to replace the right hand speed control for the cruise control on my 2008 Chrysler Aspen - any ideas? Anyone!


11_18_2011_12_24_34_am.gif
REPLACING CRUISE CONTROL SWITCH

1.
Disconnect and isolate negative battery cable from battery.

2. Remove airbag module (See AIRBAG REMOVAL below).

3. Remove speed control switch mounting screw and remove switch from steering wheel.

4. Reverse procedure to install.
AIRBAG REMOVAL
1. Disconnect and isolate negative battery cable from battery.

2. From the underside of the steering wheel, remove the two screws that secure the driver airbag to the steering wheel armature.
CAUTION: The horn switch and the clockspring pigtails connected to the back of the airbag module are fragile. Do not pull on these wires to disengage them. These must be handled carefully to prevent damage to the horn switch and/or the clockspring assembly.
3. Pull the driver airbag away from the steering wheel enough to access the three electrical connections on the back of the airbag housing.

4. Disconnect the steering wheel wire harness connector for the horn switch from the horn switch feed pigtail wire connector, which is located on the back of the driver airbag housing.

5. The clockspring driver airbag pigtail wire connectors are secured by integral latches to the airbag inflator connector receptacles, which are located on the back of the driver airbag housing. Depress the latches on each side of the connector insulator and pull the insulators straight out from the airbag inflator to disconnect them from the receptacles.

6. Remove the driver airbag from the steering wheel.

7. Reverse procedure to install.

Nov 17, 2011 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...