Question about Cars & Trucks

1 Answer

Doe it matter how the harmonic balancer goes on a 2005 pt cruiser?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

Yes it does matter

Posted on Dec 07, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

LiquidPT
  • 9 Answers

SOURCE: 2005 Chrysler PT Cruiser Whinning noise

If it's on turning, it sounds like the power steering pump. Could also be your belts (power steering & and/or accessory) need changing

Posted on Jun 14, 2009

  • 10 Answers

SOURCE: DIAGNOSTIC code P01A4 for pt cruiser

my old amns cruiser has the same problem i'm putting it down to loss of turbo pressure as the inlet manifold is leaking when reved
i'll let you know when manifold is replaced if it cures it

Posted on Sep 09, 2009

  • 615 Answers

SOURCE: '05 PT Cruiser O2 sensor problems.

I had a similar problem with my car. It turned out the O2 sensors were fine and the issue was a leak in the throttle body causing the engine to run lean. If you have an ODB2 scanner you can look at fuel trims, etc and will be able to tell.

Posted on Mar 28, 2010

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the torque spec on a harmonic balancer on a pt cruiser


you need the Chilton book for your car go to auto zone , advance all the auto stores carry them and look in the torque specifications section it is in there

Aug 27, 2014 | 2004 Chrysler PT Cruiser

1 Answer

HOW DO YOU GET THE HARMONIC BALENCER PULLEY OFF


There should be 4-6 bolts around inside outer edge of pulley attaching it to balancer.

Aug 12, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Pcm is bad on our 2005 pt cruiser, and chrysler dealer said that they are back ordered and they have no idea when they will be able to get us one. does anyone know of a dealership in ohio or the US for...


Try Auto Computer Exchange. They aren't new, but re-manufactured computers. I checked and they have exchanges in stock - you can also send in yours and have them re-build/repair it.

May 27, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Does all 2005 pt cruisers have the same wiring harness?


Go to PT forum BEST in the INTERNET

http://www.ptcruiserlinks.com/forum/

all question answered by PT owners

Jun 11, 2010 | 2005 Chrysler PT Cruiser

1 Answer

I have a 2008 pt cruiser. The engine light is on


mcdevito75 here, Yes a crankshaft sensor could cause your mentioned problems, the sensor should be located near the Harmonic balancer, you may need a special tool to remove it and if I'm not mistaken the new sensor thakes an adjustment, Have auto zone change this sensor for you, even if you succeed, how often will you change this sensor.

May 14, 2010 | 2005 Chrysler PT Cruiser

3 Answers

Horn does not work


Where is the fuse for the horn on a PT Cruiser

Apr 09, 2009 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...