Question about Dodge Avenger

Open Question

How do I change the alternator on my Dodge Avenger?

I need to know where the alternator is located and how to remove.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: location for turn signal relay

It depends on the model of avenger you have, coupe or convertible. It can either be in the steering column with the multifuntcion switch(basically the turn signal lever and wiper control asembly) or it is in the center console behind the radio.

Posted on Sep 08, 2008

simard2
  • 124 Answers

SOURCE: changing a clutch on a manual dodge avenger 96

Try going to http://autozone.com and see if they have some helpful information for your problem.

Thank you for using Fix Ya!

Don't forget to rate to overall satisfaction of this answer.

Good Luck!

Posted on Jan 29, 2009

  • 6 Answers

SOURCE: dodge avenger 2008

It depends on who you go to and if you want it done right. I went to the Dealership and had them put front brakes on my 2008 Dodge Avenger and it has been in the shop every 2-4 months since then for front brakes. They replaced the entire front brake system and my 08 Avenger is still eating brakes. I finally took it to a friend who owns a auto repair shop he replace the rotors which are total about 115.00 for each from AutoZone and replaced the brake pads for 50.00 so it cost me just parts 155.00 and my Avenger is running smoothly since haven't had problems with the brakes since. Go to Midas and let them change it for roughly 89.00 avoid the dealership at all cost they can run 200.00-500.00 depending on if it is just the brakes pads or if it is the rotors and pads.

Posted on Jun 02, 2009

rickachett
  • 14 Answers

SOURCE: How to change a headlight bulb on a 1999 dodge avenger?

under the hood in behind the head light is where the bulb goes dont touch the glass on your new bulb

Posted on Jul 28, 2009

  • 1 Answer

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 genesis 8 cylinder alternator removal


you need a garage as you have to recover and disconnect the a/c refrigerant.

2010 alternator removal

then I found this

It's a little tricky.
I recently had to replace mine, it was still under warranty.

You don't have to removed any of the motor mounts.
A quick review of the process.

Release the pressure on the belt tensioner and remove
The belt around the alternator.
On the top left corner of the alternator you'll see a 10mm
Bolt bracket holding the alternator wires. Remove that 10mm bolt.
Then the alternator connector and power wire. A 12mm nut.
Then to remove the alternator you must remove the bracket which holds the alternator,
Which is the tricky part. The alternator has 2 14mm bolts holding it to the bracket, the bracket has 4 14mm bolts and
A 12mm bolt on the front. Two of the 14mm bolts are located behind the alternator.
Which means you would have to move the alternator toward the front of the car to reach the two bolts.
Then remove the bracket and alternator together. Then you would have to follow in reverse order to properly reach
Those 2 14mm behind the alternator.

It's going to seem like impossible especially your first time.
The Hyundai instruction just shows to remove the belt, under covers and the alternator. Literally.
I don't know where your located but I'm in Miami. If that's any help, we can do it together no issues.

Thread Need Help Does anyone have write up to replace alternator 2014...

remove alternator for 2012 4 6 genesis Google Search

Jul 25, 2017 | Cars & Trucks

1 Answer

How do I remove and replace an alternator on a 2008 Nissian Altima


Make a note of the radio code if coded and then disconnect the negative terminal of the battery. IF YOU DON'T KNOW THE CODE AND IT IS A CODED RADIO, don't disconnect the battery and proceed with extreme caution removing the alternator cable without shorting to the engine! Locate the alternator, disconnect the cable, slacken the tension bracket and remove the fan belt. Remove the tension bracket bolt on the alternator and remove the bolts under the alternator.
To replace it reverse the procedure.

Mar 04, 2017 | Cars & Trucks

1 Answer

How to remove the alternator


Before the step-by-step instructions I want to make sure this is the Alternator that needs to be replaced and not something else. This will save you money for an Alternator you don't need and save you time for replacing a good alternator.
Start the vehicle. With the engine running - disconnect the Negative Cable from the Battery. If the Engine dies - it is the Alternator. If it doesn't die - it is not the Alternator. I have had plenty of people who have replaced perfectly good Alternators only to find out it was something else.
Step-by-step:
1. Disconnect the Negative Cable from the Battery.
2. Using a 15mm closed end wrench/bar - Rotate the Belt Tensioner towards the front of the vehicle and remove the Surpentine Belt off the Alternator. You do not have to take it completely off the vehicle.
3. Remove the bolt holding the top of the Alternator Mounting Bracket to the Engine Intake.
4. Remove the bolts (plural) holding the outside of the Alternator Mounting Bracket to the Alternator Mounting Plate.
5. Remove the bolt holding the top of the Alternator to Alternator Mounting Bracket.
6. Remove the Alternator Mounting Plate.
7. Remove the the Altenator Mouting Bracket.
8. Rotate the Alternator towards the rear.
9. Discoonect the electrical connections (plural), including the nut holding the wire on.
10. Remove the lower Pivot bolt located at the bottom of the alternator.
11. Remove the alternator.
12. Installation is reverse of above.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Dec 15, 2009 | 1999 Plymouth Voyager

1 Answer

Where is the alternator located on a 2006 Ford Taurus?


Hi,

If yours is the 3.0L (2 valve) engine, then location will be obvious - next to the degas bottle on the engine.

However....if it's the 3.0L (4 valve) engine, then:
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt.
  3. Remove the power steering hose bracket nut from the alternator mounting bolt.
  4. Remove the upper alternator mounting bolts. NOTE: The left side bolt will come out with the alternator.
  5. Raise and safely support the vehicle.
  6. Remove the right front wheel.
  7. Remove the right inner fender splash shield.
  8. Remove the screws and the alternator splash shield
  9. Remove the torque converter inspection cover.
  10. Install the flywheel holding tool.
  11. Remove the bolt and the crankshaft pulley. NOTE: The crankshaft pulley bolt has a reverse thread. The crankshaft pulley and bolt are a molded composite and are one piece.
  12. Lower the alternator to allow access to the electrical connectors.
  13. Disconnect the crankshaft sensor.
  14. Release the oxygen sensor connector locator from the bracket.
  15. Remove the lower alternator bolt.
  16. Disconnect the regulator electrical connector.
  17. Disconnect the remaining wiring from the alternator and remove the alternator
I know....what a pain !


Cheers,

Scott

Nov 12, 2009 | 2006 Ford Taurus

2 Answers

Do you know where the alternator is located on a 97 isuzu trooper?


On the drivers side on the bottom front of the engine.

Oct 03, 2009 | 1997 Isuzu Trooper

2 Answers

Need to know location of coolant temp sensor in 2003 Impala


Usually found either on thermostat housing or close by on the lintake manifold. Usually can be removed with a regular wrench.

Mar 04, 2009 | 2002 Chevrolet Blazer

1 Answer

Altenator


Unplug the alternator remove ground to motor.
Remove serpentine belt.
remove 2 bolts which hold alternator.
replace reverse of removal.
4 out of 10 difficulty.
Only special tool you will need is a wrench long enough to pull back the tensioner.
See the radiator support for location of tensioner and serpentine routing.
While its off, i would suggest replacing the belt too.

Dec 26, 2008 | 1999 Ford Windstar

1 Answer

Need to know how hard it is to replace alternator on 2001sephia


The alternator is located behind the head of the engine on the passenger side of the vehicle. There are 3 bolts that will have to be loosen or removed so the alternator can be removed too. Also the electrical wires will need to be removed. There should be at least 2 of them. One snaps or pulls off and the other can be loosen with a 10 mm wrench of socket. You'll need a 12 mm socket or wrench and a 14 mm wrench or socket to get to the bolts. Once that is acquired, the alternator should come right off. You'll need to go under the vehicle to gain access to the bottom bolt of the alternator. Replace the new one in reverse order.

Dec 15, 2008 | 2001 Kia Sephia

2 Answers

Need to know how to change the alternator properly


There are three bolts: tensioner bolt on bottom two bolts on top and they are tough; three wires: ground, power, and harness.
Disconnect negative battery cable, remove all wires from alternator, remove drive belt. Locate all bolts: remove tensioner bolt and mounting bolts, then remove alternator from below. It comes off easier than it goes back on.
Install is reverse order of removal. be sure to label wires for easier replacement.
This videoclip might help you and you can find for more

Good Luck

Dec 14, 2008 | 1998 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...