Question about 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Removing rear bumper cover on 2007 Chevrolet Impala?

I have dent in the plastic bumper, need to push out dent.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 271 Answers

Most dents can be popped or tapped back out, provided it has not crumpled or creased the metal.


---------------------------obd2express.co.uk

Posted on Dec 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 14036 Answers

SOURCE: 2003 Chevrolet Impala LS.

RAISE REAR VECHICLE SUPPORT VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED SAFELY SUPPORTED BY JACK STANDS. WORKING UNDER VECHICLE BUMPER DETACH THE FASTENERS SECURING THE BOTTOM OF THE BUMPER COVER. REMOVE THE SCREWS SECURING THE BUMPER COVER IN THE REAR WHEEL OPENINGS.OPEN TRUNK AND REMOVE THE SCREWS SECURING THE UPPER EDGE OF THE BUMPER COVER PULL THE BUMPER COVER OUT AND AWAY FROM THE VECHICLE.

Posted on Aug 12, 2011

  • 1311 Answers

SOURCE: l want to fix my

Attached is a figure of the bumper area, go to www.compnine.com and enter your vehicle info, then click on the Group 7 diagram, go down to the front bumper section and click on the diagram. Item part numbers will be listed.

freddyboy61_12.gif

Posted on Aug 29, 2011

  • 10865 Answers

SOURCE: i need a new rear bumper for my 2002 chevy monte

you will need the bumper and the mounting bolts. A junk yard will be your best bet for cheap. look in the yellow pages and start calling around until you find a good shop that does the work for a fair price.

Posted on Sep 12, 2009

Testimonial: "thank you :)"

co7196
  • 3433 Answers

SOURCE: how to replace 2009 chevy silverado 2500hd rear

Unless they change everything, the bumper just bolys on. Fisconnect the tow plug and what ever else and take the bolts out of the brackets attached to the frame, Good Luck, Ned-

Posted on Sep 16, 2009

Ben-mrfixit
  • 68 Answers

SOURCE: front bumper cover support

sounds like you need a new front end clip

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair a dent in the rear bumper of my 2004 Honda pilot? Do I have to remove the bumper and if so how is that done?


depending if its plastic you can remove the dent using a heat gun and a tap around the bump usually pop out. removing the bumper there are screws on the sides behind the wheel arch covers and 4 bolts around 1 foot away from the corners, if your model has sensors in the bumper they will need to be discounted. also any other wires that are they before you pull off the bumper.

Jun 20, 2017 | Honda Cars & Trucks

1 Answer

Removing rear bumper cover for 2007 uplander


Lift the tail gate. There are clips or screws along the top edge. Remove this. The clips all you do is pull the center pin with a panel tool or pliers then the rest will come out. Then you will need to remove the clips holding the rear side of each of the back wheel wells in. Under that will be more clips, screws or bolts that hold the side edges of the bumper cover on.

Aug 19, 2016 | 2007 Chevrolet Uplander

1 Answer

How to remove rear bumper cover on a 2003 chevy impala?


The top and bottom are held in place by plastic plugs. Where the bumper meets the metal, There are two bolts on each side.

Jun 29, 2016 | 2003 Chevrolet Impala

1 Answer

I have a small dent in front bumper. Iwant to heat it to pop it out.what do I remove in back to push to push it out.


The plastic cover is usually over something too rigid to allow pushing out. Normally you have to take the plastic cover off, pop it out, and then put it back on.

Feb 10, 2016 | 2012 Buick LaCrosse Base Sedan 2.4L 4-cyl....

1 Answer

I want to push out a dent in the rear plastic bumper but I have to take it off first.


Probably so. I have seen people use a round ended bar to push through the foam backing and force the dent back out. I have also seen someone use Insulating foam (used to seal around door & windows of houses) to spray into the dent. When the foam cures it expands thus pushing the dent out and providing new foam to help it stay there.

Feb 14, 2011 | Nissan Versa Cars & Trucks

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

2 Answers

My Toyota Corolla rear bumper has at big dent on


you have to take the whole bumper off and the bolt the u see holding it on the re-bar and bumper cover should come off

Jul 01, 2009 | 2000 Toyota Corolla

1 Answer

Toyota Sienna bumper dent


These vans have a styrofoam bumper wrapped in semi-rigid plastic. When you dented the bumper you probably dented the styrofoam as well, so depending on how deep the dent is you may not be able to bring it back to normal.

The surest way to fix the dent would be to remove the bumper by unbolting it, then taking out the styrofoam and pushing out the dent.

Apr 03, 2009 | 2006 Toyota Sienna

2 Answers

Dented rear bumper, how does bumper detach to pound out?


is it a rubber bumper? use suction cups, thats what dent specialist use instead of takin off the entire bumper. use a winshield dashboard suction cup for example. Just be creative...

Sep 30, 2008 | 2006 Kia Sportage

1 Answer

Rear Bumper Cover


you would need to heat it up from behind to remove the dent and the rubbing compound should work as long as it hasnt penetrated your paint layer

Jun 07, 2008 | 2001 Ford Taurus

Not finding what you are looking for?
2007 Chevrolet Impala LS Sedan New Cars Logo

1,628 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...