Question about Land Rover Cars & Trucks

Open Question

1998 range rover codes p1447

Replaced the purge valve and pulled canister to be certain it was working properly. noticed that there is a place at the side of Vent control valve that takes a plug in but there is no plug in the engine bay that would fit there.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

motor1258
  • 6674 Answers

SOURCE: emission test showed error code p1443.check engine

You might want to try "google images" just type in your vehicle and what your looking for. Here's an example (link) of what to look for.

http://www.fordmuscle.com/forums/attachments/all-ford-techboard/4132d1212515121-code-p1443-help-96tbird_evap.jpg

Posted on Oct 25, 2009

  • 173 Answers

SOURCE: Check Engine light---P1445 Vapor Canister purge

Hello... It is located under the rear center of the vehicle, behind the axle.

Good Luck....

Posted on Dec 25, 2009

HD Road King
  • 70 Answers

SOURCE: 2006 gmc sierra 1500 4.3 . check engine light on.

More than likely the evaporator vent valve.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the purge control valve located on 1998 nissian pathfinder


Location should be back by the fuel tank.

first off, the P1447 DTC is triggered when the EVAP control system isn't operating properly or there is a leak between the intake manifold and the pressure sensor. the parts between the pressure sensor and intake manifold are:

1. EVAP canister purge control solenoid valve
2. EVAP canister purge control valve
3. EVAP canister purge volume control valve (Part # 14930-3M201) YOU WILL HAVE TO DOUBLE CHECK ON THE PART NUMBER WITH THE DEALER FOR THE PRICE.

If you've received this P1447 DTC, chances are that the brick of charcoal in the canister has fallen apart over time, and filled the lines with charcoal. this affects parts 2 & 3 from the above list, and of course the EVAP canister (Part # 14950-1s717 $144.22). but when you replace the canister, you have to replace the EVAP canister vent control valve (part # 14935-54u06 about $100), and don't forget the o-ring (part # 16618-40u00 about $1.60) that goes between the canister and the vent control valve.

If you attack this DTC early enough, all you have to replace is the canister and vent control valve with the o-ring, which will add up to under $300 MSRP...a lot better than paying upwards of $1000 for parts and labor. Don't be scared to do it, it's actually quite simple.

D

Sep 28, 2015 | Cars & Trucks

1 Answer

I have a 1997 Nissan Pickup XE L4 2.4 vin S 2389cc KA24E Fi MFI GAS SOHC got a code p0110 and also p1447 just replaced the MAP sensor and TPS Fuel filter and EVAP i checked w/ OBD came up w/ IAT ...


The IAT sensor is located in the air filter case on top of the throttle body. If you remove the air filter you can see it on the left side of the case on the bottom. It connects from underneath and the connector can easily be damaged if you are not careful when removing the lower part of the air filter housing from the throttle body. If you replaced the MAP sensor you may have damaged the connector or pulled a wire loose.

The p1447 problem indicates a leaky evap system which could be as simple as a bad gas cap or as in my case a bad evap canister and vacuum canister cut/bypass valve.(http://ww2.justanswer.com/uploads/fixurnissan/2012-02-04_230002_1.pdf)

If your evap canister has ruptured then your evap lines will be full of carbon pellets. You will need to disconnect each end (evap canister line towards front) and evap canister purge line towards the rear and blow out these lines with compressed air. Once they are clear replace the evap canister and check the vacuum canister cut/bypass valve as described in the link. If you fix this your self you will save close to $1000 as opposed to what a dealer would charge to fix this problem.

Oct 27, 2013 | 1997 Nissan Pickup

1 Answer

What does code p1447 mean ...???


The code says "evap purge flow monitor fault"
Possible causes include ...
- EVAP canister purge volume control solenoid valve stuck closed.
- EVAP control system pressure sensor and its circuit.
- Loose, disconnected, or improper connection of rubber tube.
- Blocked rubber tube.
- Blocked or bent rubber tube to MAP/BARO switch solenoid valve.
- Cracked EVAP canister.
- EVAP canister purge volume control solenoid valve.
- Closed Throttle Position Switch.
- Improper connection of one-way valve.
- Blocked purge port.
- EVAP canister vent control valve.


This is a "jackpot" code. It points to so many possible causes as to be almost useless.

Feb 15, 2013 | 1996 Nissan Maxima

1 Answer

2004 BMW 325i I have a code p1447 do you know were to fix?


Fault codes do not have a single reason for being set, there are multiple reasons. here is the info you need to know about this code.
P1447 - Evaporative Emission Control System Purge Flow Monitor
Possible causes- EVAP canister purge volume control solenoid valve stuck closed
- EVAP control system pressure sensor and the circuit
- Loose, disconnected or improper connection of rubber tube
- Blocked rubber tube
- Cracked EVAP canister
- EVAP canister purge volume control solenoid valve circuit
- Closed throttle position switch
- Blocked purge port
- Closed throttle position switch

Jun 13, 2012 | Cars & Trucks

1 Answer

Code 1447 nissan sentra


P1447 purge volume control solenoid valve
Usually charcoal canister has ruptured and vehicle needs canister.
entire system will have charcoal pellets in it. pull the hose at solenoid and see. solenoid can sometimes be cleaned by tapping and blowing with your mouth not compressed air. sometimes needs to be replaced. remove canister and remove pressure sensor(by canister and blow out charcoal with compressed air. wear safety glasses. you will need to blow from both ends several times. don't give up at first nothing comes out and when you pull air gun away charcoal comes out on your hands from pressure release

Jun 01, 2012 | 1996 Nissan Maxima

1 Answer

PO440 code on a 1999 chev tahoe


P0440 - Evaporative Emission Control System Malfunction
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0440 could mean one or more of the following has happened:
The gas cap is not installed or working properly
The purge solenoid has failed
The canister is plugged and not working properly

Possible Solutions: with a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

Check it and keep us updated.

Aug 13, 2011 | 1999 Chevrolet Tahoe

2 Answers

I have a code P1447 Evap purge flow monitor on my 97 Pathfinder. What is and how do I correct this issue?


P1447 - Evaporative Emission (EVAP) Control System, Purge Flow Monitor
In this evaporative emission (EVAP) control system, purge flow occurs during non-closed throttle conditions. Purge volume is related to air intake volume. Under normal purge conditions (non-closed throttle), the EVAP canister purge volume control solenoid valve is open to admit purge flow. Purge flow exposes the EVAP control system pressure sensor to intake manifold vacuum.

Under normal conditions (non-closed throttle), sensor output voltage indicates if pressure drop and purge flow are adequate. If not, a fault is determined. Malfunction is detected when EVAP control system does not operate properly, EVAP control system has a leak between intake manifold and EVAP control system pressure sensor.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
* EVAP canister purge volume control solenoid valve stuck closed
* EVAP control system pressure sensor and the circuit
* Loose, disconnected or improper connection of rubber tube
* Blocked rubber tube
* Cracked EVAP canister
* EVAP canister purge volume control solenoid valve circuit
* Closed throttle position switch
* Blocked purge port
* Closed throttle position switch


Test is and send us your updated.

Jan 14, 2011 | 1998 Nissan Pathfinder

1 Answer

2004 niisan infinty g35x code p2135


NISSAN OBDII DTC

P1105 Manifold Absolute Pressure/Barometric Pressure Switch Solenoid Circuit

P1110 Intake Valve Timing Control Circuit (Bank 1)

P1120 Secondary Throttle Position Sensor Circuit

P1125 Tandem Throttle Position Sensor Circuit

P1132 Intake Valve Timing Control Position Sensor (Bank 1)

P1135 Intake Valve Timing Control Circuit (Bank 2)

P1137 Intake Valve Timing Control Position Sensor (Bank 2)

P1140 Intake Valve Timing Control Position Sensor (Bank 1)

P1145 Intake Valve Timing Control Position Sensor (Bank 2)

P1148 Closed Loop Fault Detected (Bank 1)

P1168 Closed Loop Fault Detected (Bank 2)

P1210 Traction Control System Signal Fault

P1220 Fuel Pump Control Module Fault

P1320 Ignition Control Signal Fault

P1335 Crankshaft Position Sensor Circuit

P1336 Crankshaft Position Sensor circuit

P1400 EGR/EVAP Control Solenoid Circuit

P1401 EGR Temperature Sensor Circuit

P1402 EGR System Fault Detected

P1440 EVAP Canister System Leak Detected

P1441 EVAP Vacuum Cut Valve Bypass Valve Circuit

P1443 EVAP Canister Control Vacuum Switch Circuit

P1444 EVAP Canister Purge Volume Control Valve Circuit

P1445 EVAP Purge Volume Control Valve

P1446 EVAP Canister Vent Valve Circuit

P1447 EVAP Canister Purge Flow/Volume Control Valve Circuit

P1448 EVAP Vent Control Valve Circuit

P1490 EVAP Vent Control Valve/Bypass Valve Circuit

P1491 EVAP Vacuum Cut Valve/Bypass Valve Circuit

P1492 EVAP Canister Purge Control Valve/Solenoid Valve

P1605 Transmission Control Module A/T Diagnosis Communication Line Fault

P1705 Throttle Position Switch Circuit

P1706 Park Neutral Position Switch Circuit

P1760 Overrun Clutch Solenoid Valve Circuit
P1900 Cooling Fan Control Circuit
sorry but your code reader is not reading manufacturers codes ,if an american market vehicle then you should be able to read them but if this is a europeon model then how did you manage to get this code??

P0235....Turbo/Super Charger Boost Sensor 'A' Circuit

this is a generic code if its any help

Nov 02, 2010 | 2004 Infiniti G35 Sport Coupe

2 Answers

P 2138 code with service engine soon light on?


Accelerator Pedal Position Error.

P2138 - Accelerator Pedal Position Sensor Circuit Range / Performance Problem

Clear the code - if it recurs, change the sensor.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 15, 2010 | 2006 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...