Question about 2004 Honda Civic

Open Question

2004 honda civic crankshaft sensor replace

Crankshaft sensor removal

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 337 Answers

SOURCE: Replacing crank shaft position sensor on 2000 Honda Civic

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018f5b9

Posted on Dec 10, 2008

Ad
  • 491 Answers

SOURCE: Replace crankshaft position sensor

Remove the left front wheel....(drivers side). Remove all accessory belts. Remove the crankshaft shaft pulley.......remove the plastic lower timing belt cover.....and there it is! It is mounted with one bolt.
The wiring runs down the right side of the timing cover while looking at it from the drivers side of the car.

Posted on Aug 17, 2009

Testimonial: "I ended up having my mechanic do the work. He did say he had to move all those parts to get to the sensor. "

  • 548 Answers

SOURCE: interior door panel removal 04 honda civic

you must carefully pop off the door plastic clips using a screwdriver and prying gently until they pop out , also remove the screws under any small round plastic screw cover inserts and in the plastic door handle area

Posted on Sep 19, 2009

leedavidian
  • 1420 Answers

SOURCE: P0335 Crankshaft position sensor location - honda

Welcome to FIxYa.com


3fb2cb2.jpg


Regards, Lee Davidian


Thank you for using FixYa,com.

Posted on Oct 24, 2010

SOURCE: 2004 honda civic is there

You will need a wiring diagram to know
where to start testing

You don't replace the sensor until you
know it is bad and have tested it

Posted on Mar 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the puller needed to remove the crankshaft pulley on a 1991 Honda Civic LX??


Once you remove the bolt the balancer should slide right out.

Oct 16, 2012 | 1991 Honda Civic

1 Answer

How do I fix a Interruption in TDC #1 sensor circuit problem on a 2001 Honda Civic? THe code is P1361 and P1362


P1361 is a misfire code, and P1362 is a TDC sensor (or crankshaft position sensor) code. The known possible repair is to replace the crankshaft position sensor. You may have to ask for a tdc sensor as some parts providers follow the mfr's part name.

Sep 08, 2011 | 2002 Honda Civic

1 Answer

Where is the harmonic blalancer on the honda civic ex 2004


The harmonic balancer is part of the crankshaft pulley. If you look close it will have a solid metal core and a thin rubber layer and then another metal part on the outer part.

Aug 21, 2011 | 2004 Honda Civic

1 Answer

2004 honda civic is there a way to test to see if wires are shorted out on the crankshaft sensor wires before replacing the crankshaft sensor it self?


You will need a wiring diagram to know
where to start testing

You don't replace the sensor until you
know it is bad and have tested it

Mar 14, 2011 | Honda Civic Cars & Trucks

1 Answer

The check engine light recently came on in my 2004 Honda Civic and the car proceeded to lose power and shut off repeatedly. After running the diagnostic it indicated that the crankshaft sensor needed to...


Check engine light means emissions control system failure.
I would only rely on Honda to properly diagnose this and
replace component failure with Honda part. The ck engine
light was probably reset when your mechanic replaced the
crankshaft sensor, and in time, came back on cause the
problem has not been corrected.

Jan 21, 2011 | 2004 Honda Civic

2 Answers

Replace crankshaft position sensor


Remove the left front wheel....(drivers side). Remove all accessory belts. Remove the crankshaft shaft pulley.......remove the plastic lower timing belt cover.....and there it is! It is mounted with one bolt.
The wiring runs down the right side of the timing cover while looking at it from the drivers side of the car.

Aug 17, 2009 | 1998 Honda Civic

Not finding what you are looking for?
2004 Honda Civic Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

79024 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...