Question about 2005 Jeep Grand Cherokee

Open Question

2011 grand cherokee DTC report

Engine light is on. Trying to determine how to get report on what the problem is. I know there was a DTC report on WK1 models. How do I get this report on the WK2 models?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

FoRdMaStEr
  • 51 Answers

SOURCE: how to replace head light bulb in 2001 grand cherokee?

Pop the hood and look at the top of the headlight capsule. you should see a single 7mm bolt somewhere in the middle. remove the bolt completely it should be about 6 inches long. once the bolt is removed then use a large flat screwdriver and carefully pry the headlight capsule out from it retaing clips. once the capsule is out then you have 100% access to the bulbs

Posted on Jan 15, 2009

alenjogy
  • 123 Answers

SOURCE: recieve "dtc report" and "transmission tempertaure"

go to workshop

Posted on Jul 17, 2009

  • 1071 Answers

SOURCE: 2003 Jeep Grand Cherokee check engine light stays

go to autozone they will check codes for free

Posted on Jul 23, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 grand cherokee engine starts butwill not move

P1784 low reverse pressure switch sense circuit.
Start by checking fluid level and condition. then check electrical connections. if all ok, probably solenoid in the valve body assembly.

P1767 Transmission Relay Always On. Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Start with the simple and Check your fuses and transmission fluid level, if the level is good and the condition of the fluid is good. There may be an issue with your solenoid or your transmission pump. You can check your pump buy checking your transmission fluid level with the engine not running and take note where the level is. Then start the engine and check the fluid level again, if the level has gone down. The your pump is good, if it does not go down. Then your pump has gone bad and your going to have to rebuilt the transmission or replace the pump.

You better of replacing the whole transmission of the pump has gone bad, since the low transmission fluid pressure would have worn out most for your clutches throughout the transmission.

Thank you for using Fixya and hope is just a simple Solenoid that has gone bad or a wire harness that has shorted out.

Posted on Nov 24, 2010

jturcotte
  • 8142 Answers

SOURCE: want to know whats these

Hi, the first part is data taken along with the code. The code P1281 indicates the engine is running cold (141 degrees--should be at least 190). Is your temp gage running lower than you are used to? If yes, it may be your thermostat has failed open. I have pasted below instructions for replacing the thermostat. Please let me know if you have any questions, and thanks for using FixYa.


3.7L & 4.7L Engines WARNING Do not loosen radiator drain **** with system hot and pressurized. Serious burns from coolant can occur.


NOTE Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse. If thermostat is being replaced, be sure that replacement is specified thermostat for vehicle model and engine type.

  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat.

To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on timing chain cover.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 115 inch lbs. (13 Nm).
    CAUTION Housing must be tightened evenly and thermostat must be centered into recessed groove in timing chain cover. If not, it may result in a cracked housing, damaged timing chain cover threads or coolant leaks.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.


Removal & Installation, 4.0 liter engine

  1. Disconnect the negative battery cable.
  2. If necessary, disconnect the coolant temperature sensor electrical connector.
  3. Disconnect the upper radiator hose from the thermostat housing.
  4. Remove the attaching bolts and lift the housing from the engine.
jturcotte_407.jpg
Remove the thermostat and gasket.
To install:
  1. Clean all gasket surfaces thoroughly.
  2. Place the thermostat in the housing with the spring inside the engine.
  3. Install a new gasket with a small amount of sealing compound applied to both sides.
  4. Install the water outlet and tighten the mounting bolts to 200 inch lbs. (23 Nm) on V-8 engines and 15 ft. lbs. (20 Nm) on non-8 cylinder engines.
  5. Install the upper radiator hose to the housing and tighten the hose clamp.
  6. Connect the coolant temperature sensor connector to the housing.
  7. Refill the cooling system.

Posted on Apr 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Should the pcm on a 99 jeep grand cherokee laredo be changed if a while back the wires were crossed during a battery jump and now the obd is able to give a reading and it stalls out


what are the fault codes reading first
If you feel that the ECM has a problem in itself and not reacting to a faulty sensor get a known good ECM and swap it out as a test

Dec 23, 2015 | 1999 Jeep Grand Cherokee

1 Answer

How do I reset the displayed messages in the EVIC for a 2011 Jeep Grand Cherokee$


sCAN IT
GET THE DTC errors
the read the FSM for that error and do the tests for that problem and correct it,
then using in scan tool reset it. bam down.

but wait no messages stated. could be just be the normal service messages.? like change oil?
or tires low. or? the glove box. operators guide.
open it and read the page on EVIC errors. bingo, its all covered there.
if it is serious error, see my first paragraph here.

Oct 19, 2014 | 2011 Jeep Grand Cherokee

1 Answer

Dtc u0100


did you scan the PCM? with a scan tool and then report all errors?
big fail if not.
U0100 - Lost Communication With Engine Control Module

Jan 04, 2014 | 2006 Jeep Grand Cherokee

1 Answer

My 1999 Chrysler town & country limited my engine light came on. I whent to get a test done, it said DTC Reported P0505= idle control system malfunction P0351= Ignition Coil A Primery/secondary Circuit...


-Possible causes are Faulty Idle Control System motor
- Idle Control System motor harness is open or shorted
- Idle Control System motor circuit poor electrical connection
- Faulty Powertrain or Engine Control Module
- Vaccum leaks or damaged hoses or improper routing check for vaccum leaks first if this was helpful please leave good feed back


Read more: http://engine-codes.com/p0505_chrysler.html#ixzz3Mq1J8Bho

Oct 29, 2013 | 2007 Jeep Grand Cherokee Overland

1 Answer

Engine Light On. How to determine code for problem?


Phone there customer service office to find out what the recall is about or the dealer, being that it is a 2011, Issn,t there still some warranty left on it,?

Dec 07, 2012 | 2011 Jeep Grand Cherokee

2 Answers

How to reset change oil light on 2011 Jeep Grand Cherokee


Try this turn ignition switch on engine off and push gas pedal to the floor 3 times

Jan 12, 2012 | Cars & Trucks

1 Answer

1999 jeep grand cherokee. starts with a little help from stepping on the gas. will idle for 2 minutes the die. help please


With a code reader connected to the DTC connection, are there any trouble codes stored? Is there an engine light lit? You will need a code reader to at least start a diagnosis and also a fuel pressure gauge.

Jul 27, 2011 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...