Question about Cars & Trucks

Open Question

I have two a212b & three 215d and I lost all the fuses and the holder all together at the same time . And it really makes me wonder how is tha possible ? . I bought them from guitar center in LA ... But then I could not find . Is it possible to purchase the holder and the right fuse for ecsh and everyone of them from you ? I need a help from you to get them as soon as possible . My cell # is 323-767-7757 and e-Mai , vaggie90640@yahoo .com and my address is To Vahak Sakajian 401 bluff rd Montebello Ca 90640 USA

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: 2006 Toyota Matrix 2nd fuse panel location?

The second fuse panel that you seek is under the dashboard, on the driver side (for a US car). This box is called the "JB1" (junction block #1), and contains several relays in addition to the 15 amp "CIG" fuse that you need to replace.
Hope this helps, and thanks for choosing FixYa!
Happy Thanksgiving!

Posted on Nov 25, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New flasher relay good fuse no four way flasher no turn signals


you need to check the bulbs holders and wiring even a blown bulb will not blow the fuse and an damaged wire or bulb holder will as it will make earth and live go together. there are also fuses for left side and right side turning lights cannot remember rating think they are 10amp.

Mar 19, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Blower motor runspart time .i have replaced resistor and relay/1996 grand am


Since you have replaced the stepped speed control resistor, the problem is probably due to a corroded connector or fuse holder.I'd check the fuse holder first, then do the possibly annoying tracing of wiring to locate a connector which may be heat- or corrosion damaged.
Finding the right color codes to follow and make locating connectors is much easier (not easy, just easier) with a manual and I like Haynes. We have three different and keep them in the vehicles to which they belong.

Nov 10, 2011 | 1996 Pontiac Grand Am

1 Answer

The fuse box under the hood, one of the fuse insert is broke so I need to replace the whole box. I need help to find the part ant the name of the part


You can call it a fuse box or panel. The unit usually comes as part of the harness. You can usually find a good used unit in most scrapyards or, you can make a "work around" by detaching the box and locating the wiring that feeds and is served the broken fuse holder. Then, all you need to do is buy an in-line fuse holder and bypass the original by attaching the wires from the holder to the backside of the panel. Use one rated at or above whatever the fuse you are replacing and use the same fuse that belongs there. If you do this, the only caution is to make sure you don't pinch any wires when you put it back together. It sounds complicated but it's far easier than installing a complete unit and it shouldn't cost you more than $10.00.

May 11, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Please help ,i have a 1990 jeep wrangler, while removing the fuse i broke the connector that the fuse goes into. what is it called and where can i get one?


Since you did not mention where the fuse was, you really haven't given enough info. But, if the fuse is in a fuse block, either the under dash one or the power distribution center under the hood, probably the easiest way to do that repair without replacing the entire block would be to take it apart so you can access the wiring inside, behind the one you broke, then get an in-line fuse holder. Attach it to the wiring that goes to the broken port and put the appropriate size fuse in it.When putting it back together, be sure not to pinch any wires including the new ones. Locate the fuse holder near the original block so you can get to it.
When buying the holder, note that they come rated for different draw fuses. Get one that is close to the one you will be using but don't use one that is rated lower. Using a 20 amp holder and a 15 amp fuse is fine but the other way around is not.

Mar 17, 2011 | 1990 Jeep Wrangler

1 Answer

Replacing a aftermarket stereo in my 2000 eclipse gs


I had the same exact problem with my wife's 2003 eclipse. Her sun roof, center display, key fobs/ alarm, radio 2000 Mitsubishi Eclipse

1 Answer

Just wondering if you can help me with a electrial wiring problem? the wires have melted together and dont know which one is the earth as they keep blowing the fuses


I would think your best bet is to cut out the melted section and reconnect (through splices) the wires. They should be color coded, so you should know which wires connect together.

If you get the wires separated where the melted part is, spliced together, and properly insulated, which one is the ground really shouldn't matter. You have removed the point where the positive is touching the negative, and the fuse blowing should stop.

I would suggest you use heat shrink tubing to insulate the spliced wires.

Oct 20, 2009 | 1991 Toyota Land Cruiser

2 Answers

My cup holder in the dash of my 1999 Jetta GL is broken and i was wondering how to remove it and put a new one in


There are spring clips on the right and left side. Squeeze them together and pull the unit out by holding onto the door.

Aug 12, 2009 | 1999 Volkswagen New Jetta

1 Answer

Can u leve n 4wd all tha time,or do i have to change back to fwd


It is not recomended to run like that all the time. It is really just for towing. If it seems to be running better I would suspect that either the rear or the viscous is in need of attention. Hope this helps and have a good day.

Jun 12, 2009 | 1991 Subaru XT6

1 Answer

1996 Dodge Dakota No Headlights or Tailights


Headlights are direct wired through switch.Check under dash to see if you had rodents inside tha may have chewed wiring.Make sure all power wires are reconnected back at battery.Check all fuses thoroughly.hope this helps

May 15, 2009 | 1996 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...