Question about Chevrolet Silverado 2500HD

Open Question

Rear wheel studs chevy 2500hd - Silverado 2500HD Chevrolet Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

davidsspa572
  • 51 Answers

SOURCE: wheel studs or bolts

Hello Miguel Thank you for using FixYa.com my name is David I hope this Helps you out.
Studs often get damaged from overtightening or from cross threading a nut on the threads. A damaged stud is replaced by unscrewing it from the part and installing a new one of the exact same size.
Stud replacement can be difficult because the stud has often been in place for a long period of time. There has been constant heating and cooling, corrosion, and rust buildup between the stud threads and the internal threads of the part. These factors combine to make some studs very difficult to remove.
The first step in stud removal is to use penetrating fluid to remove the corrosion to free the stud from its mating threads. Soak the area of the threads with penetrating fluid. Allowing the fluid to soak into the threads overnight will make it easier to remove the stud.
Before removing the old stud, measure the distance it sticks up from the surface. This measurement will be needed later when installing the new stud. Use a 6-inch scale to measure from the part surface to the top of the stud. Write the measurement down so it can be referred to later.
A stud remove is used to remove studs. It is installed over the stud. The jaws on the stud remover grip the outside of the stud. A wrench fits on the stud remover and allows the technician to rotate the stud in a counterclockwise direction to remove the stud.
If a stud remover is not available, a stud can be removed with two nuts. Locate two nuts that are the correct thread size. To thread onto the stud. Start one nut and thread it all the way down to the bottom of the stud. This nut will be the drive nut. Start another nut and thread it down until it contacts the first nut. This is called the jam nut.
Put a wrench on the bottom drive nut and hold it in place. Put another wrench on the jam nut and tighten, or "jam" it against the drive nut. The jam nut will now hold the drive nut in position on the stud.
Now put an open-end wrench on the bottom drive nut. Turn the nut in a counterclockwise direction. Turning the nut in this direction causes it to want to unscrew the stud. Instead the forces cause the stud to unscrew.
When the old stud is out, inspect the internal thread. If it appears rusty or damaged, clean up the thread by running the correct size tap through the threads as previously explained. Compare the new stud with the old one. The studs should be exactly the same thread size and the same length.
Check the vehicle's service manual to determine if the threads of the new stud should be coated. If the stud should be locked in place and not easily removed, you may need to use a threadlocking compound or threadsealing compound. Threadlocking compounds are on studs and other fasteners when vibration might cause them to unscrew. Thread sealants are used when a stud extends where liquids, such as oil or coolant, could get on the fastener.
Antiseize compound is used on the stud threads to prevent the stud from reacting with the metal on the internal threads. If this happens, the stud could stick or seize. Antiseize compound prevents this reaction and makes the stud easier to remove the next time.
After the new stud is properly coated, it can be installed. Start the stud by hand, making sure it enters the threads securely. Turn the stud in as far as possible by hand before using any tools. Then use two nuts as described earlier to drive the stud into the part. Use the depth measurement made on the old stud to be sure it is driven in the correct depth.

upper_left.gif grey_line.gif upper_right.gif grey_line.gif Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z grey_line.gif lower_left.gif grey_line.gif lower_right.gif Related Parts: grey_line.gif 0900823d80050bfd.gif Wheel Nut

Posted on Nov 06, 2008

jpstuhr
  • 49 Answers

SOURCE: Changing the wheel studs for '87 Chevy Cavlier

Need Tool - Front Hub Spindle Remover
22f87f7.jpg

Posted on Feb 12, 2009

VWdan
  • 114 Answers

SOURCE: broken wheel stud

1. get new studs and nuts
2.remove wheel
3. remove caliper at bracket to spindle connection(2 18mm bolts?)you may need to remove caliper from bracket,but not always nessacery. Or remove drum,then to #5
4.remove rotor,will need a hammer, tap inbetween studs dont wreck good studs and see if new studs can be installed without removing parking brake shoes. If there is no clearance to get new stud in you will need to remove shoes.
5.Pound out old studs place new stud in hole use a washer on outside then put a nut on and tighten to install stud, A air gun or some type of impact tool will be very helpful. Check to see that stud has enough threds to pull stud all the way thru ,add more washers if nessecary dont let the nut run out of threds it will **** to get back off and wreck new stud.
6. if you dont have air gun or feel comfertable removing brakes bring it to a reputable garage, shouldnt cost more than $70+ parts to get all new studs put in on one wheel.

Posted on May 17, 2009

  • 770 Answers

SOURCE: 89 4x4 pu broken wheel stud

Will have to remove LR drum, The stud should drive out fairly easily, as a precaution, apply penetrating oil and let soak prior to driving it out. Install the new stud..about a $4 item, (compared to $100 to get one fixed at the toyota store, then put your wheel back on, snug up all lugs then torque to 83 ft/lbs.

Posted on Jun 19, 2009

  • 574 Answers

SOURCE: rear wheel studs were bent one snap i recently

you can or if you can get them through the holes where you can put a couple of nuts on them you can pull them through with impact or lug wrench. dont over torque only

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver's side rear brake or wheel seems to lock up for short bursts while at low speed only noticed on a left forward turn into a parking spot.96 Chevy Z71 4x4


possible limited diff action making both rear wheels drive
wheel bearing failure or adjustment
brake drum or wheel loose on studs

Jul 31, 2017 | Cars & Trucks

1 Answer

How to replace a rear wheel stud


remove the wheel
using a hammer and punch knock the broken stud out
fit the new stud from behind use over size nuts as spacers fit the stud nut and apply tension
using the hammer and punch from the rear on the head of the stud knock it in as you keep the tension on the stud nut
keep the process going until the stud is fully seated on the head of the stud

Jul 10, 2014 | 2005 Toyota Camry Solara

1 Answer

Removing rear wheel studs


there should be one spot while turning rear wheel bearing that will allow one stud to be knocked out and new stud replaced BEFORE trying to remove the next stud... one at a time

May 16, 2014 | 2008 Chrysler Aspen

1 Answer

Chevy camao


Not necessary to remove axles. Remove drum or rotor, hammer through the damaged stud, has room to fall out behind axle flange. Insert new stud through opening, A stud installer is preferred at this point, however, you can also use a couple of stacked washers and a lug nut. grease the washers, place them over the stud, grease the stud threads and then thread on the lug nut. With a socket wrench ,crank the stud down. The splines on the stud will bite in , keep turning until stud base meets axle flange. A new lug nut may be required , the one you use as an install tool may get damaged.

Jan 08, 2014 | 1998 Chevrolet Camaro

1 Answer

2001 altima replacing rear wheel stud


strip it down to your hub the hub holds the studs .it is a push pull fit .but an old nut on it.then hit the top of it .it when then push in.remove the nut. push in the new stud from the rear of the hub.put a larger nut on top of stud ,then your wheel nut to pull the stud into the hub.then remove the wheel nut .then refit the parts taken off.and fit your wheel.

Dec 30, 2013 | 2005 Chrysler PT Cruiser

1 Answer

2005 chevy 4x42500hd


Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...