Question about Ford Cars & Trucks

Open Question

Power seat won't work on 2005 ford 500 - Ford Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bschilz
  • 2049 Answers

SOURCE: Heated Drivers Seat Ford 500 2006 will not work.

It is usually one of two problems. Either the relay under the seat has failed or the heat element in the seat has failed.

If you are not electrically challenged, you can use a simple volt-ohm meter and check for continuity in the heat element. If you have continuity, the element is good, otherwise that's your problem.

If the heat element is good, you may want to take the good relay from under the passenger seat and put it on the driver's side to see if that fixes it. If so, then you have to get a new relay.

Last, but very unlikely, would be a bad switch.

Posted on Jan 10, 2010

Ad
  • 514 Answers

SOURCE: 2005 ford 500 - seat

look in your owners manual for the seat relay location and see if it is clicking while the switch is pushed, if not, then replace it.

Posted on Apr 04, 2011

  • 368 Answers

SOURCE: 2005 ford 500 seat won't

I don't know for sure about the Ford 500 but in general the manufacturers don't have a lot of room for extra fuses and wires so probably only one fuse goes to the seat or seats. I would find the fuse box and hopefully the fuses are all labeled.

I assume the seat at one time went forward and backward. What can stop it from doing this is something like a rock getting in the gear and stopping the motor from moving or maybe just dying on its own. It could instead be a wire or connector.

I hope this helps.

Posted on Sep 18, 2011

  • 1 Answer

SOURCE: My 2005 Ford Escape just won't start this

most likely a dead battery

Posted on Jul 26, 2012

skychief2001
  • 21873 Answers

SOURCE: 98 ford taurus flooded... power locks, windows, seat won't work now

I would expect to find a main wiring connector has some serious corrosion in it.
The fuses for those circuits would be in the fuse box in the engine compartment.
You could try running power direct to the driver's door switch to make the windows come down. Make sure you have a fuse or breaker in the line.

Posted on Sep 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford 500, won't start a lock light is


need to reprogram ignition key security system when battery disconnected. turn ignition key to the on position for 3 to 10 seconds until the lock light goes out then start vechicle.if lock light dont turn off turn ignition switch to on position 30 seconds until lock light turn off.

Jun 12, 2013 | Cars & Trucks

1 Answer

Driver power seat won't move.


check the fuse box as it ay just be a blown fuse, also check the wireing connectors under the seat as they may have come loose.
martyn

Apr 08, 2013 | 2010 Ford F-150

1 Answer

Air bag code 33 for a 2005 lincoln town car


2005 Towncar SRS Code 33 (3 flash + 3 flash, repeat this set for twice. then Beep 5 times pause x 5 = 25 beeps every 30min).

This means you have problem with left (Driver) side pretentioner (Seat belt retract system).
It doesn't mean physical belt or retract mechanism.It is just bomb wiring which is part of airbag system.
When airbag deploy, passenger must stay tight in seat otherwise body lean to front then slam back to seat by airbag.
if belt is loose or delay to lock, passenger's body rocks back and forth.So, system use small bomb (Fire power) to lock and retract seat belt when airbag deploy.There is small bomb and igniter in part of Seat belt retractor.
Code 33 is warning for this part on 2005 Towncar.(older model is different meaning in Ford/Lincoln, it's possibly passenger side airbag system for earlier model)
Before you work for any part of Airbag system and touch any "Yellow connector", * *Disconnect battery (negative side is good enough) and wait at least 5 min to clear all power in system**.(Airbag store back up power for few minutes to be able to deploy even in case if power disconnected)
by the way, you should move your driver seat most forwarded position before you disconnect battery to make it easy to work with seat belt.
locate driver side seat belt retractor (in center pillar between front and rear door, you may have to fight with weather strip)

Locate Yellow connector on bottom of Seat belt retractor (it's called "Pretensioner")it is located on very bottom of rear side of retractor.
only one yellow connector. (make sure your battery is disconnected)
Check its physical connection or looseness.if connection looks fine, you may have to replace whole seat belt ($180-$200 in Lincoln dealer)
You can check if pretensionor is good or bad by regular tester, but unless you know how, I won't tell (because I don't wan't you to blow out pretentionor).








Jul 19, 2012 | 2005 Lincoln Town Car

1 Answer

I have a 2005 ford crown victoria P71 ( interceptor). It has cruise but dosent work. I just bought it from the county. It was a active patrol car that was up for replacement (so its in excellent mechanical...


I also have that same vehicle but, I'm sorry to say it does not have cruise. I also have a wiring issue. I replaced the interior (seats, carpet, door panels, and a few dash moldings) with duel power seats, however I through out the old seats before I noted the "wiring colors" for the passenger seat 'seatbelt' and 'airbag' sensor connections. The new seats came out of a 2003 crown vic (not a p71) and had totally different connections under the passenger seat. My '05 p71 did not even have the wires there for a power passenger seat, so I had to replace and wire them in from the harness that I removed from donor car. That actually wasn't TOO bad, and the seats work fine, but I don't know which wires go together for the seatbelt and airbag sensors, as the old wire 'colors' under the seat do not match the 'colors' on the connectors under the new power passenger seat. If you could tell me the colors of the wires to your original seat (passenger), for the seatbelt and airbag plugs you would be a great help in solving my issue with the "airbag" and "seatbelt" light that stays lit on the dash. If I can help with your problem in some way, even though my car does not have cruise, e-mail me and let me know how (ccandrllc@aol.com) .

Dec 18, 2011 | 2005 Ford Crown Victoria

1 Answer

2005 ford 500 seat won't go forward, but will go up and down and lean back don't have manual to check right fuse.


I don't know for sure about the Ford 500 but in general the manufacturers don't have a lot of room for extra fuses and wires so probably only one fuse goes to the seat or seats. I would find the fuse box and hopefully the fuses are all labeled.

I assume the seat at one time went forward and backward. What can stop it from doing this is something like a rock getting in the gear and stopping the motor from moving or maybe just dying on its own. It could instead be a wire or connector.

I hope this helps.

Sep 18, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

My daughter's 2005 grand prix will not start. How can she get in the trunk to get to her jumper cables because the key fob won't work to open the trunk and the inside trunk release won't work...


In your situation I think your best bet is going to be taking out the back seat. Luckily this is very easy and will allow you easy access to your truck and jumper cables. Okay in order to remove the back seat you will have to have a socket set. There should be 2 bolts holding the bottom of the seat down and you can find them on the floor on the front part of the rear seat. One bolt on the driver side and one bolt on the passenger side. After you get those bolts out you should be able to remove the bottom section of the seat. If you can not look for two more bolts on the back part of the seat. You will have to look between the back of the seat and the bottom part. After you take those two bolts out both parts of the seat should be free and you can remove them. I hope this helps.

Aug 25, 2011 | 2005 Pontiac Grand Prix

1 Answer

Seat warmer ford 500


2005 Ford 500 Limited can't start due to anti theft device, is there a reset I can hit

Apr 01, 2009 | 2007 Ford Five Hundred Limited Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...