Question about Cars & Trucks

Open Question

Reattach 98 gmc sonoma front bumper cover

Plastic front bumper cover fell off. I saw two bolts under the bumper beam that plastic tabs from the cover attach to. Are there top attachments and end ones? The pictures in adds for replacement ones don't show the tabs or attachment points. Haynes manual shows nothing. I can fabricate attachments, just need to know how it goes on. Thankx.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 140 Answers

SOURCE: need to replace the front bumper cover on a 1995 ford escort

its just the bumper cover.. once you buy the bumper cover it will replace your broke one,, however you my need to buy a bumpercover support..i think its only about $30 more..good luck keith...

Posted on Mar 15, 2009

Ad
  • 73 Answers

SOURCE: 99 VW Beetle Hood Release Cable plastic tab broke

the only way to purchase is a whole cable

Posted on Jul 01, 2009

  • 1 Answer

SOURCE: Ihave a 98 gmc jimmy that the wiper motor

how do you remove wiper motor 98 jimmy

Posted on Jul 29, 2009

ftw1952
  • 10319 Answers

SOURCE: I have a 1999 Chevy Lumina car. I had to replace

It is a vacuum holding cell which is needed to feed vacuum to the heater air condioning controls inside your car. Also other vacuum related items feed off this vacuum tank

Posted on Apr 15, 2010

Testimonial: "Thank you very much. You explained this very well. Thank you again!"

johnjohn2
  • 5763 Answers

SOURCE: one side of front bumper cover is hanging down on my 98 handa

You should remove the bumper cover and take a look and make sure that the cover is not broken, its all plastic and the hold down arms sometimes break off and bumper will hang, also look for missing or loose fastners,

Posted on May 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to replace the low beam headlight plus the running ligut. I have the bulbs but need to access the back of the unit to install the bubs.


You probably won't like this answer, but unless you are a glutton for punishment, as well as highly mechanically inclined, just take the truck to a mechanic. The headlamp bulb is inside a plastic headlight assembly like a pickle in a hamburger. To get to the pickle, you first have to open the bag, unwrap the burger, then separate the burger to get to the pickle. NO JOKE.

There are a ton of plastic parts you must remove to gain access to the headlamps. These tupperware components tend to self destruct even if you are very careful. Plan on needing at least two or three new plastic GM body rivets. The splash guard and eyebrow as well as the front bumper cover must be taken loose to gain access to the bolts that secure the headlight assembly to the frame. The plastic beauty apron must be removed above the headlight assembly. The grille above and attached to the bumper cover has to be loosened as well.
25468137-epwetmasq2n0wnrof1fw5po3-5-1.jpg By the time you are actually birth the headlight assembly out of the front quarter of the fender, you'll be sorry you even tried. Then you get to dismantle the actual headlight assembly to change the lamp inside. Don't lose the dozen or two bolts, rivets, and assorted fasteners while you fight with the headlamp assembly. Test your new light before you secure all the parts back together.
This guy had to do 4 videos to illustrate the repair!!!

Feb 23, 2015 | 2008 GMC Acadia SLT-2

1 Answer

Replace remove front bumper on a 1993 gmc sonoma


Are you talking about the plastic housing part or the steel piece under that?

Sep 13, 2014 | 1993 GMC Sonoma Club

1 Answer

Change head lite bulbs 2000 toyota GTA


The easiest way to change them is to remove the 3 bolts that hold the headlight in place, 1 is directly on top of the headlight, 1 can be seen thru the upper radiator support(of course be sure to remove the plastic engine compartment covers if they are installed), and the 3rd is hidden underneath the front bumper cover, to remove the front bumper cover, move aside the inner wheel well panel nearest the sidemarker lights, pull the bumper cover off slighty fron a plastic snap lock that lines up the bumper with the fender, you should see the bolt as soon as you pull the bumper cover. Each bolt is a 10mm patern so I recommend a small ratchet with extension, once you remove the bolts, the headlights come right off. You might have a rubber cover over where the headlight bulbs are located, simlpy unscrew it, or pull it off whatever your vehicle has, I believe the bulb type is H7, its a standard low-beam bulb, keep in mind the passengerside headlamp is attached to the windshield washer refill reservoir which snaps in and out of place. Install is reverse procedure, I hope this helps, and if you need, go to Newcelica.org for ANYTHING Celica related.

Aug 11, 2010 | 2000 Toyota Celica

1 Answer

One side of front bumper cover is hanging down on my 98 handa


You should remove the bumper cover and take a look and make sure that the cover is not broken, its all plastic and the hold down arms sometimes break off and bumper will hang, also look for missing or loose fastners,

May 28, 2010 | 1998 Honda Civic

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

2 Answers

How do you remove the front bumper cover on a 98 honda accord sedan EX


Apply the parking brake and raise the vehicle and support it securely on jackstands.

Disconnect the negative battery cable, then the positive battery cable and wait two minutes before proceeding further (make sure you have the code if you have an anti-theft radio because you will need it after disconnecting the battery).

Working under the vehicle, detach the screws securing the lower edges of the bumper cover (use a small screwdriver to pop the center button up on the plastic fasteners, but do not try to remove the center buttons. They stay in the ferrules)

Remove the bolts, screws and plastic pins on each side retaining the bumper cover to the splash shields. Remove the bolt on each side where the bumper cover attaches to the fender.

Working at the top, detach the retaining bolts (2) securing the bumper cover to the hood latch support. Remove the cover.

When you put it back, make sure the tabs along the top edge of the bumper cover fit into the corresponding clips on the body before attaching the bolts and screws. An assistant is helpful.

Hope this helps you.

Jan 05, 2010 | 1998 Honda Accord

1 Answer

What do I have to do to remove the front bumper on a 2005 GMC Canyon 4wd pickup?


first remove plastic around and under bumper then acess bomper bolts from under truck make sure any lights are disconeccted before dropping bumper

Oct 06, 2009 | 2005 GMC Canyon

1 Answer

Remove right front fender on 2005 odyssey


NO 2 BOLTS ON TOP OF FENDER UNDER HOOD 1 BOLT BEHIND PLASTIC TRIM BY MIRROR PULL THIS PIECE BACK TOWARDS MIRROR OR IT WILL BREAK TABS OFF 1 BOLT UNDER ROCKER TRIM 1 SCREW INTO ROCKER AND 1 SCREW BEHIND PLASTIC SHROUD GOING INTO BUMPER FROM UNDER NEATH PULL BUMPER BACK SLIGHTY AND YOU WILL SEE A WHITE PLASTIC CLIP PULL BACK AND BEHIND THIS IS A BOLT REMOVE HEADLIGHT CLIP FROM FENDER AND LOSEN BOLT BY HINGE NOW FENDER SHOULD COME RIGHT OFF BOOK IS 2 HOURS TAKES 1 HOUR TO REMOVE BUT GOES ON IN ABOUT 30 NINUTES

Mar 16, 2009 | 2005 Honda Odyssey

1 Answer

Oil filters


Alright,

On that motor the filter is "remote" from the engine. It is located under a plastic cover directly below the front bumper.

Good Luck

Jun 30, 2008 | 1999 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...