Question about 2006 Jeep Commander

Open Question

How to remove the door panel on 2006 Jeep Commander

Need to remove the door panel to repair the handle.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

motor1258
  • 6674 Answers

SOURCE: How do I install a driver dide door handle on my

Inside handle, no, outside yes, to access nuts/bolts on back side.

Posted on Jul 31, 2009

  • 1986 Answers

SOURCE: replace exterior door handle on a jeep commander

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Posted on Oct 23, 2009

morse008
  • 1111 Answers

SOURCE: serpentine belt on a 2006 Jeep Commander, 4.7

Have you checked your owners manual... also look on the core support as you open the hood for a diagram. They are usually mounted there and possibly on the strut tower or under the hood. Also try your local library or parts store for a manual. I hope this helps you

Posted on Nov 07, 2009

  • 645 Answers

SOURCE: ac/heater fan switch problem on a 2006 jeep commander

next to the fan motor there should be a connector that has three or four wires that attached to the blower resistor. it should have two screws holding it to heater case, just pull it out and replace.

Posted on Feb 13, 2010

Testimonial: "This info was very helpful but need a little more info of where the fan motor is located. I will post another question to find that info."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I activate the 4 wheel drive in a 2006 jeep commander


well the operators guide missing in car (glove box)
sure
but is on line for free for 10 years.
get it read it?
here it is, down load it and keep it?
http://www.jeep.com/en/owners/manuals/

depends on 4wd options sold new on car.

Feb 20, 2015 | 2006 Jeep Commander

1 Answer

How do i remove engine oil pan on 2006 jeep commander 4.7


ALWAYS, ALWAYS, ALWAYS.......CONSULT A SHOP MANUAL!
YOU MAY HAVE TO REMOVE UNDER ENGINE SUPPORT COMPONENTS, EXHAUST, ++...OR IT MAY JUST UNBOLT AND DROP DOWN

Nov 24, 2014 | Jeep Cars & Trucks

1 Answer

How do I remove starter on a 2006 4.7 cylander jeep commander


Disconnect battery.
Unbolt starter, move it down a bit.
Now unbolt wires (two of them).
Now wiggle starter around and get it out. On 99-04 grand cherokee the front wheels need to be on ground (or on a ramp) or the drooping suspension gets in the way.

Jul 01, 2014 | 2006 Jeep Commander

1 Answer

How to remove 2007 jeep commander climate control panel for light bulb replacement


The lights in the climate control panel are not bulbs, they are LED and the entire panel will need to be replaced. I would check for a bad connection before replacing the panel assembly.

Dec 28, 2010 | 2006 Jeep Commander

1 Answer

Starter repair estimate 2006 jeep commander


Check here for parts replacement and "How to": Jeep/Commander/Replacement/Starter

Hope helps (remember rated this).

Jul 07, 2010 | 2006 Jeep Commander

1 Answer

Install a altenator for a 2006 jeep commander


I would rate this a 5 in difficulty. If you have a metric socket set, basic hand tools and a supertine belt tool it's fairly easy repair. You can rent a surpentine belt tool at Autozone.

Disconnect the battery
remove the cowling
remove the supertine belt from the altenator pully
disconnect the red wire on the back of the altenator
disconnect the harness plug from the altenator
remove the bolts holding the altenator to the mounting brackets.
Reverse the process with the new altenator and it it's done.
Make sure your battery is charged before you start the engine a low battery can cause damage to your new altenator.

May 20, 2010 | 2006 Jeep Commander

2 Answers

Replace exterior door handle on a jeep commander


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and disconnect the linkage to the outer door handle and then remove the bolts securing the outer handle to the door

Oct 23, 2009 | 2006 Jeep Commander

1 Answer

2006 Jeep Commander lost instrument panel power


check all fuses and battery connections start there.

Oct 13, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...