you may have damaged the ABS sensor or wire to the sensor up front check the wire that runs from the inner finder well and make sure it connected to the ABS sensor on the spindle
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
2001 Hyundai SantaFe , S.Korean car,
no country told (you ) or what engine is there, gas/diesel and displacement (size)
the classic easter egg hunt, (it's not bad leave it be)
post problems first
check fuses and scan the PCM, obd2, usa scan tool if is USA>?
2.7L V6 - Gas <<< this? answering for only this ME (guessing engine) or 2.4L?
2001-2003 Hyundai Santa Fe - ECM - Hyundai
Stock Code??? 3912138170
This part is compatible with 1 vehicle(s) matching 2001 Hyundai Santa Fe LX Sport Utility 5-Door 2.7L 2656CC V6 GAS DOHC Naturally Aspirated.
and must be programmed before use. (new /used , replaced)
the car may have
BCM, body.
PCM (TCM + ECM = PCM) SEEN ON NEVER CARS.
ECU/ECM,, BINGO?
TCM transmission
ABS
HVAC BRAIN BOX
AND MORE, (SEE SERVICE MANUAL FOR ALL THAT)
I am a mechanic ..most people ask questions about these foreign hyundai motors ..below is an example of engines that basically if you ask about a Hyundai Xg 350 ,xg300 ..well allow me to hammer 90% of your questions in case you want to grab another motor ..these motors listed will work on 90% of all hyundai products ...Look at the starter sizes ,,all the same for the selected models ..then look at the motor sizes ..This will help you in solving some problems most do not give the specific questioning 100% NEW REPLACEMENT STARTER FOR STARTER
HYUNDAI 2001 SANTA FE 2.7L ENGINE 2002 SANTA FE 2.7L ENGINE 2003 SANTA FE 2.7L ENGINE 2004 SANTA FE 2.7L ENGINE 2005 SANTA FE 2.7L ENGINE 2006 SANTA FE 2.7L ENGINE
2003 SANTA FE 3.5L ENGINE 2004 SANTA FE 3.5L ENGINE 2005 SANTA FE 3.5L ENGINE 2006 SANTA FE 3.5L ENGINE
I presume your Santa Fe sports the 3.5 liter V6 engine? If it's got the NUT, it's at the front & there's a nut stud. If it's got the BOLT, it's accessed from the opposite (anterior) side using a long, long extension. If you have a vehicle hoist/lift, you can easily see it. If you're on your back with the vehicle on jack stands, it's much more difficult to see the 14mm bolt between the exhaust flex pipe and heat shield of the exhaust manifold at the right hand side of the engine.
Say you're directly beneath the engine oil pan, move toward the transmission and look upward and forward between the 1:00 and 2:00 oclock positions of the engine (toward the power steering pump) - 14mm bolt
your whining noise might be comming from dry belts in order to pinpoint your problem have a jug of water ready before startup open the bonnet then startup if the noise appears pour water over the belts if noise goes away replace v belts
If your Santa Fe has a V6 engine 2.7L , it sounds like you have an ignition break down happening. You will need to renew all the ignition wires and check the two coils also for arcing .
×