Question about 1992 Ford Crown Victoria

1 Answer

92 crown vic transmission

Thanks for your reply, I put a used trans into the car and it worked fine before putting it in this is the same problem I had with the old trans, the reason I switched it, is there a sensor, or possibly the shift cable coming from the throttle, does that have any kind of adjustments on it

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

I dont recall any sensors forthe od...usually if the over drive goes out people drive in the d mode which is harder on the transmission but no there are no sensors that im aware of that would make the OD not work correctly

Posted on Jan 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2005 Crown Vic its been running fine it

Check the trans fluid with in neutral. If low, put some in. Would not be electrically actuated so fuses have nothing to do with your situation.

Sep 24, 2014 | 2005 Ford Crown Victoria

1 Answer

'99 Ford Crown Vic LX: #12 30A Maxi fuse blows seconds after starting or ignition turned on.

i had this problem with my 1999 jeep grand cherokee laredo with the brake lights it kept popping fuses right after the ignition was turned on try putting a higher amp fuse in place of the old one that keeps blowing then check for shorts to the starter and check grounds and wires and also the transmission issue check the fluid and then if the fluid is fine change the transmission filter the filter may have not gotten replaced when the transmission was rebuilt and may be clogged or dirty

Oct 04, 2012 | 2002 Ford Crown Victoria

1 Answer

Jeep grand cherokee will not go in to overdrive

was the computer for that exact year and model ? computers have to be matched to that same model to run the same transmission as in the vehicle example 1999 ford crown vic trans.put in a 2000 crown vic even though the trans. is the same the ccomputer reads trans. is built for 1999 cause of the program in the comp.

Sep 06, 2012 | Jeep Cherokee Cars & Trucks

3 Answers

1994 Ford Crown Vic comes out of gear just driving down the road. I let off and sometimes it catches, sometimes it takes half dozen times. Flushed trans and put seal renew in it. Still has problem, but no...

Hello john, sounds like you are having a converter lockup problem. The clutch packs may also be worn causing low pressures. Pressure test can be run to determine. Sometimes adding a a non-solvent formula additive such as Lucas transmission fix will help. It's been known to stop slipping in worn transmissions.

I hope this helps.

Sep 21, 2011 | 1994 Ford Crown Victoria

1 Answer

2004 Crown Vic tran whines in low gear only, took ...

It's normal on the AOD transmissions. Their first gear uses straight cut gear and thus has the whining noise. Gear 2, 3 and 4 are helical gears and thus quiet.

May 20, 2010 | 2004 Ford Crown Victoria

1 Answer

92 crown vic - temperature guage on the dash is not working...


The temperature gauge sending unit is located in the front section of the intake manifold, just to the right of the alternator on the 4.6L engines. Got this from autozones repair manuals

Mar 16, 2010 | 1992 Ford Crown Victoria

1 Answer

97 Crown Vic transmission issue

Check the transmission linkage cable that runs from the steering column under the dash to the trans under the car. make sure that the cable is not damaged and that all connections are tight.

Jan 05, 2010 | 1997 Ford Crown Victoria

1 Answer

I put a "97 4.6 intercepter engine in my "92 crown vic. I toke the computer, the harness that runs from the computer, harness for the engine and the trans from the "97 Crown Vic before I junked it....

I did this once, not on a Ford and this is what I had to do to get it right. Get down to your local friendly dealer or an auto electric shop, put on a sad face and tell them your story and they will probably provide you with the wiring diagrams for the 2 cars. You need both. If that won't work go to faxonautoliterature . They have a wiring diagram book for the 92 for $19 and a Ford service manual for the 97 for $69. That will give you both wiring diagrams. It is an excellent company to do business with by the way.
With the diagrams in hand start tracing wires one at a time. You will find that a lot of the wires for the same things will be different colors, on orange wire in 92 will be green in 97. I don't know why they do that but they do. This should be able to get your car functional but you may be short a few options. I never did get my cruise control sorted out. Hope this helps and best of luck.

Nov 03, 2009 | 1992 Ford Crown Victoria

1 Answer

Where is the overdrive fuse located? Thanks

this not a fuse problem, its a transmission problem , the overdrive dont have fuse

Jul 21, 2009 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5613 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides