Question about Cars & Trucks

1 Answer

Sensor diagram for a ford crown victoria 1996

Need info to complete location on vehicle where all sensors are located

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 256 Answers

Get your self a repair manual for it,

Posted on Dec 07, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Where is the fuse panel on a 1985 Ford Crown Vic located?

Local Ford dealership service department provide answer on location of the fuse panel. Fuse panel is located directly under the steering column. The cover panel is held by two screws and the power antenna swithch locking ring must be removed.

thank you all for you assistance,

Posted on Jul 01, 2008

  • 2 Answers

SOURCE: a fuse diagram for a 1998 ford crown victoria

http://www.fixya.com/cars/t816725-fuse_diagram_1998_ford_crown_victoria try this site

Posted on Aug 12, 2008

  • 36 Answers

SOURCE: a fuse diagram for a 1998 ford crown victoria

Contact your local Ford dealer. I'm sure they will help you out. 

Posted on Dec 12, 2008

  • 4369 Answers

SOURCE: 1998 ford crown victoria fuse box diagram

it should be in your owner manual. if not, I can look up something for you but can't post illustrations to this site.

Posted on Jan 09, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is transmission speed sensor located


There are multiple speed sensors in the transmission. I assume you're referring to the vehicle speed sensor which is also known as the output shaft speed sensor which is located in the tailshaft housing.

Jul 29, 2015 | 2006 Ford Crown Victoria

1 Answer

Where is the cooling fan sensor located at on a


You'll find said sensor on the lower radiator tank. Just look for a wire connected to a sensor screwed into the lower tank and that's it.

Sep 24, 2014 | 2003 Ford Crown Victoria

1 Answer

Coolant Temperature Sensor 2003 Ford Crown Victoria 4.6L SFI 8cyl


Usually found right before or right after the thermostat.

May 02, 2014 | 1996 Ford Crown Victoria

1 Answer

I need the location of the crankshaft position sensor on my 1994 ford crown Victoria police interceptor.


Hi there:
On 1994 Ford Crown Victoria 4.6L SFI 8cyl the Crankshaft Position Sensor is located under hood, center, lower engine area, front side of engine, passenger side of crankshaft pulley, mounted in engine block.

11_20_2012_8_33_40_pm.gif


Fig. 2: Remove the retaining bolt for the CKP sensor and remove the sensor from the front cover

Disconnect the negative battery cable.
Remove the accessory drive belt from the engine.
Raise and safely support the vehicle.
Remove the A/C compressor mounting bolts, but do not disconnect the A/C lines. Remove and support the compressor out of the way.
Detach the electrical connector for the CKP sensor.
Remove the CKP sensor retaining bolts and remove the CKP sensor.

To install:
Installation is the reverse of removal.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 20, 2012 | Cars & Trucks

1 Answer

Location of vehicl;e speed sensor


where would the output speed sensor be located

Jul 25, 2011 | 1999 Ford Crown Victoria

1 Answer

Where would the 02 sensores for a 1997 ford crown victoia be located on the vehicle


the two pre-cat sensors are the exhaust pipe(s) just after the manifolds, the two downstream sensors are between the first and second cat(s) on the H-pipe.

Sep 02, 2010 | 1997 Ford Crown Victoria

1 Answer

2000 ford crown victoria


hello lipounds , the temp sensor located on the passenger side front of engine near the #1 injector . hope that fix ya .

Jan 02, 2009 | 2000 Ford Crown Victoria

1 Answer

Can not find where the head sensor is located


looking at the engine from the front on the inside of the cylinder head at the front of the engine below the upper intake

Nov 26, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...