Question about 1997 Jeep Grand Cherokee

1 Answer

Blower Motor Power Cable/Connector Fried

1997 Jeep Grand Cherokee Limited. Blower Motor works fine, but the electrical cable leading from the power distribution module has a fried connector on it... Is it possible to replace this cable?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

A Used Parts Yard would Have toe Whole Shooting Match and THIS IS WHAT I WOULD ADVISE AS the Power Core Fried for a reason power distribution module and all. Unless you Wish to Purchased all New ORDERED From DEALER

Posted on Jan 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower motor stopped working


Bad blower motor ? First unplug connector at blower motor , use test light to check for electric power is getting to it, if there's power to it. This will also eliminate your fuse , relay or wiring to blower motor. You could use a jumper wires from your battery to check the blower motor also . You could try this first , if you like. Let us know how it comes out. Have a Blessed Day.. Luther.

Jul 03, 2014 | 1994 Jeep Grand Cherokee

2 Answers

What besides the blower motor can make the ac not work on a 2001 jeep grand cherokee limited not work


There is an electronic fan speed control module screwed to the blower. It's hard to remove under dash. I took it to workbench and found bad solder connection. I resoldered it and re-installed it. Working fine for over a year now. Saved $350. But hard work.

Jun 28, 2014 | 1997 Jeep Grand Cherokee

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Blower not working on 2002 jeep grand cherokee, Need electrical schematic.


check the wires going to the blower motor for power on both sides if you get power on both sides of blower motor the problem is a bad blower motor resistor if you got power coming in on one side only you have a bad blower motor.

Feb 07, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Power to blower motor but no grond at the motor


replace the blower motor resistor, this will solve your problem, the resistor is located on heater box, its screwed into box near blower motor, wires from blower go to this resistor, unplug the connector, remove screws and slide out of box, hope this is helpful.

Dec 26, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Where is the blower motor resistor located in the 1997 jeep grand cherokee larado?


IT IS UNDER THE GLOVE BOX NEXT TO THE BLOWER MOTOR.IT WILL HAVE 2 DIFFERENT ELECTRICAL CONNECTOR

May 07, 2009 | 1997 Jeep Grand Cherokee

1 Answer

1998 Grand Cherokee blower not working


Check blower fuse, relay and power at blower motor harness terminal. Check for proper grounding at dashboard and body as well. Yo
good lucku can run a hot wire to the blower motor and touch it to the connector spade to check if blower itself is OK. There are other components in the system, but this is a good start! Don't forget...fuses blow because there is a problem elsewhere. If you replace one and it blows again, there is something else wrong!

Jan 15, 2009 | 1997 Jeep Grand Cherokee

2 Answers

Heat


we had same problem .ran new wire to blower . old wire broke down ck wires with ohm meter.

Dec 19, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...