Question about 1998 Plymouth Voyager

1 Answer

Nocompressionvalve#6 blows compression thur valve#6 will not idle

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Filmmaker:

    Uploaded 5 video answers.

  • Expert
  • 141 Answers

Not sure what you are asking, you found the problem ....the valve is not seated properly in its seat or the edge of the valve is burned or the valve seat has slipped out of place make sure you are on the compression stroke for that cylinder before condemning the valvetrain

Posted on Dec 07, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Saturn SL... Began putting while driving. Sluggish response to pedal. Now starts, revs to about 3000, then dies. Changed the ECTS, Cleaned the EGR... Still won't hold idle. HELP PLEASE!!!


Try cleaning the throttle valve and the idle speed control air bypass valve. Only use throttle valve spray cleaner and harsh abrasives, soak them and clean with the throttle valve with a soft cloth. Soak the idle speed control valve for an hour and then blow it out with compressed air.

May 26, 2016 | Saturn Cars & Trucks

1 Answer

Rough idle multipule misfire


Hi. The most common cause that I have found for an " only idle misfire" is low compression. The engine needs at least 100 psi of "dry " compression to idle smoothly in most cases and if any cylinders are higher or lower by more than 20 percent of any other cylinder, you will also have an idle misfire condition felt. Should you perform a compression test, make sure to disable the igntion system completely, not just move the ignition wires out of the way as you will still have spark and the fuel injectors will still inject fuel in nearby proximity to possible ignition source. Always perform two tests, "dry" and "wet" compression. "Dry" is warm engine with spark plugs removed. "Wet" is after performing "dry" test add a few drops of light oil into cylinders and perform compression test again to see if the number rise. If they rise, you have worn piston rings or cylinder walls. If they do not rise, you likely have worn valve seats, misadjusted valves, or head gasket issues, possibly cracks in the cylinder head. If you need to know how to compression test with a tester in detail, message me back and I can help. I'm assuming you may already know due to the fact you state you replaced all the parts likely by yourself so you probably have strong technical merit.

Aug 09, 2012 | 1999 Honda Civic

1 Answer

I have a problem with my econovan, i havent had a service done to it in over 6 months and now when i took it to a guy to service it, its been blowing blue / white smoke only on cold motor so i did some...


Hello, I have several suggestions for you. Your problems can still be with the cause of the blue smoke. You need to get a compression test done on the motor either with an elaborate test machine at a Dealer or Tune-up shop or use an old-fashion compression gauge. With the valve cover off and engine running you can also push on the valve spring with your thumb and weak valve springs will cause the engine to miss. Sometimes the weak springs can be detected with a Vacuum gauge, showing a bouncing needle. Your valve stems may be gummed up from the bad oil seals you changed.

The blue smoke is also a sign that the oil rings for the pistons are worn out or have rotated to give a bad seal. When the engine warms, the rings expand and helps eliminate the smoke. Check your sparkplugs for oil staining. Your sparkplugs may be fouled and this condition is called "blow-by".

You can check and clean your EGR valve because it needs to seat or your engine can not idle smoothly. Check the Intake manifold for loose bolts, then use a water mist around the seams to see if the Intake gasket is leaking. Just use an old spray bottle filled with water and spray the engine while it is running.

I hope my solutions are very helpful to you in finding the problem.

May 09, 2011 | Ford Econoline Cars & Trucks

1 Answer

Cleaned out carburator on a F100 straight 6. Now


I would suspect there is dirt in the idle system, did you blow the jets and passages out with compressed air.

Jun 04, 2010 | 1981 Ford F 100

1 Answer

Smokes after idling 2-5 minutes very heavy then clears


bad valve guides or o ring bushings to valves or slow blow buy in rings have to do compression check to tell the diff.

Nov 25, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Mitsubishi 1991 model 4g15 engine replaced head gasket now it starts a bit on idle if i try to rev it it stalls and cuts off and starts turning backwards. if I remove a plug where there is compression a...


the blowing air out is good, means the valves and rings are good. the rest of the problems seem like your valve timming chain is out, did you replace or remove it? has anything to do with ignition been touched?

Nov 03, 2009 | 1997 Mitsubishi Mirage

1 Answer

Ford Thunderbird 96 V6 3.8 Idle rough, smokes like big Diesel motor


CHECK ENGINE COMPRESSION.SOUND LIKE YOU HAVE WORN ENGINE VALVES AND PISTON RINGS AND VALVE SEALS IF ENGINE SMOKING BLUE.IF YOU ARE GETTING HEAVY WHITE SMOKE.YOU HAVE A BLOWN HEAD GASKET.WHEN DOING COMPRESSION TEST IF COMPRESSION READINGS 90 - 80 WORN RINGS 60 - 40 BLOWED HEAD GASKET.

Aug 29, 2009 | 1996 Ford Thunderbird LX

1 Answer

Engine idle speed


Sounds like you idle air control valve is starting to mess up. You can actually take this off and clean it with throttle body cleaner and it should help get your idle back to normal. As is sounds the idle air control valve controls how fast/slow your car idles. It is located on the throttle body normally held on with a couple of screws. The throttle body is where the air duct hose coming from the air filter box ends at the engine block. Here is a picture of what you are looking for: a483326.jpg
Make sure that you clean the valve portion and not the electrical plug with the throttle body cleaner. Let it air dry or blow lightly with compressed air before putting it back on. Let me know if you have any more questions. Thanks for using FixYa!

Aug 01, 2009 | 1998 Ford Escort

1 Answer

Rough idle,blow by ; blows oil cap into my hand when i unscrew it no water in the oil,checked injectors they seem good could it be head gasket?


Do a compression test to the cylinders, you could have a burnt valve or bad piston ring. Keep me posted, if you can not get a compression test gauge you can always do the oil school method and pull the spark plugs and read the spark plugs condition's. Good luck and be glad to help.

Jun 11, 2009 | 2004 Dodge Ram 2500

2 Answers

1998 ford escort


replace the idle speed control air bypass valve.

Mar 02, 2009 | 1987 Ford Escort

Not finding what you are looking for?
1998 Plymouth Voyager Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...