Question about Cars & Trucks

Open Question

How do you remove the nylon pin from the top of a bathroom stall door

I am a maintenance person who is in need of removing a toilet stall door but do not know how to remove the nylon pin from the top hinge.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: 2001 Blazer door hinge pins and bushing replacement

you need a special spring compressing tool to remove and reinstall the hinge spring and then its a matter of removing the door installing the new bushing and rehang the door with new pins ive tried doing this while leaving the door on the car trust me its just harder that way good luck and please rate -jeff

Posted on Sep 01, 2008

  • 150 Answers

SOURCE: my problem is that the upper door hinge on my 2001

Most likely the hinge is not bad, but the hinge pin bushings are bad. You can buy the hinge pins and the bushings at your local auto parts store. They come in a kit. Hope this info is helpful.

Posted on Mar 22, 2009

  • 1 Answer

SOURCE: need to remove barn doors on a 92 suburban

You do not have to pull the hinge. I just did one. The pins need to be pressed out. We used a bearing press. It is a 4 hour job. Locate the pins fisrt and you will see why they won't pound out.

Posted on Mar 22, 2009

  • 8 Answers

SOURCE: changing rear brake pads on 2002 buick lesabre

Your correct, does hinge on top bolt and then is ussually stiff pulling from pin, but it will move

Posted on Jul 01, 2009

  • 1071 Answers

SOURCE: how do you remove hinge pin on side door of E-150

you need to support the door and re[lace one pin and busgtbg at a time knock them out with a hammer and punch

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

99 Chevy Silverado door pins how to change hinges


If the hinges are bolted they can be released from the bodywork and door by removing the bolts although on many models accessing the bolts can be a very difficult task.

In the case of welded hinges the door must be removed by removing the hinge pins. There is then a lot of careful grinding and cutting to remove the hinge parts from the door and the bodywork and new hinges welded into place.

In the case of a car regularly maintained, including oiling the hinges, removing the hinge pins with a dedicated service tool is relatively easy but can be extremely difficult without the service tool. Cars that have not received a high level of maintenance throughout it's life hinge pins can be extremely difficult to remove needing the application of heat, lots of hammering and repainting afterwards.

Oct 17, 2015 | Cars & Trucks

2 Answers

What are some good websites for information & pictures of remodeled small bathrooms using ceramic tile?


This is the car and truck section, but you might try youtube for videos.

Dec 18, 2012 | Cars & Trucks

1 Answer

REMOVAL OF DOOR PANEL


You need to remove the door handle/window winder and sometimes the door lock button. Then the rest of the door panel is held on by expanding nylon pins which pop out wit the insertion of some kind of wedge - like a screwdriver -protected to keep the paint from scraching, or a sharp wood dowel.

Nov 26, 2011 | 1999 Volkswagen Beetle

1 Answer

Replacing the back hatch (door). I need to get the handle free to change out the key barrel. There is a long nylon threaded screw holding one end of the handle from inside the door panel. Once I get this...


I don't remember having a long nylon screw in this. Open the hatch, remove the sheet metal screws that work with the push pins to secure the interior cover. After removing those screws carefully pry the push pins up till they come free from the hatch. This will give you access to the lock assembly. remove the "C" clamp that holds the lock in place after disconnecting any rods that maybe attached to it and the lock should come out toward the outside of the vehicle. There should be no reason to remove the molding.

May 15, 2011 | 1999 Plymouth Voyager

1 Answer

Looking for cabin filter


  1. From inside vehicle, release hood.
  2. Remove four quarter turn nylon push pins retaining RH cowl vent screen
  3. Remove push-on clips retaining RH cowl vent screen and remove RH cowl vent screen from vehicle.
  4. Remove two screws and remove cowl top inner panel shield from vehicle.
  5. (RH IS THE PASSENGER SIDE THE COWL IS THE PLASTIC PIECE AROUND WHERE THE WIPER BLADES ARE)

Dec 03, 2010 | 1999 Ford Taurus

1 Answer

How do you put a bmw exterior door handel in


remove all inner door trim, and inner window trim, release 2 nylon blocks on top of window scissors and slide window up and out, on outside remove plastic handle trim and undo large nut round doorlock, on edge of door pop out plastic plug and undo coonecting rods, inside door at front of handle is a little cir clip holding a pin through handle, remove both, you should now be able to wriggle handle out to the inside of the car remember to watch for wires to micro switch for cental locking, rebulild is a reveral of this.

Jun 27, 2010 | 1994 BMW 3 Series

1 Answer

I need to replace side mirror on the passenger side,but not sure how to remove door panal to getto the plug


First roll down the window and remove the inside mirror cover the remove the push pins in the back of the door panel ( push the center in to the 1st click then remove the pin from the door panel . With the pin out of the door panel push the center pin back out of the push pin retainer so it will be ready to go back in)Then remove the screw cover behind the door pull (just pops out) remove the 2 screws . Use a door tirm tool to release the push pin retainers that hold the trim to the door and lift the door panel up and off the top edge of the door . disconnect the elec connectors.

Feb 23, 2010 | 2006 Chevrolet Malibu

1 Answer

How do you open the side door panel to a 2001 Oldsmobile Alero?


Become a detective all screws that are hidden including in the door rest -look for inserts that can be lightly pried out some have them hiding the door in the door rest -using a door panel remover(found at most auto parts stores) start at lower edge of door pulling the nylon door snaps out from the frame-as you progress you use your feel if all screws have been removed .some nylon snaps will need a little coaxing.

Sep 24, 2009 | 2000 Oldsmobile Alero

1 Answer

Removing the front door panel


there a special tool to remove that clip or you can use a women nylon slip the nylon beetween the handle and door panel and move it be carefull that clip fly off when it loose thanks pierre

Oct 08, 2008 | 1999 Chevrolet Malibu

2 Answers

Removal of door gromet


I would just get a unibit and drill a hole, put some protective loom and run the wire through, i cant really tell you how to correctly remove the gromet because i need to see it in person.

Good luck..

Jun 12, 2008 | Volkswagen Beetle Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...