Question about 1999 Chrysler 300M

Open Question

2004 chrysler 300m- purchased and installed T-one wire harness connector from reese, (includes convertor) If my car's headlights are off, my trailer turn and brake signals work fine. As soon as I

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 34 Answers

SOURCE: I installed a 4-wire Vehicle End connector on my

maybe bad ground wire>?

Posted on Oct 11, 2009

  • 36 Answers

SOURCE: Hello, I just noticed the

CHECK THE BULB SOCKET WITH A VOLT METER. IF YOU ARE GETTING VOLTAGE, THEN CHECK THE BULBS WITH AN OHM METER, & SEE IF THE BULBS ARE REALLY GOOD. IF YOU DON'T HAVE AN VOLT/OHM METER, IT WOULD PROBABLY BE CHEAPER TO JUST REPLACE BOTH BULBS.

Posted on Aug 11, 2010

dttech
  • 4803 Answers

SOURCE: 2004 Chrys Concorde, new utility

Your vehicle CANNOT be wired for a trailer without using the converter box. The only vehicles that do not require a converter box are the vehicles that use the stop lamp bulb as a turn signal. Your vehicle is equipped with SEPARATE stop lamp and turn signal bulbs.

To make the converter box work correctly, it must be wired according to the instructions to BOTH the stop lamps AND the turn lamps. The tail (or PARK) lamps DO NOT go through the converter box.
Your trailer uses the SAME bulb for stop and turn - THIS is the reason you need a converter.

The wire color for both your LEFT TURN and your RIGHT TURN are LIGHT GREEN/TAN. Although the wire colors are the same at the bulb sockets, these are SEPARATE circuits and must be wired to the correct wire at the converter box. (LEFT and RIGHT) The converter box will have an INPUT connection for EACH of these.

The wire color for your STOP lamps is WHITE/TAN. The converter box should only have one INPUT wire that connects to this. It doesn't matter which side of the vehicle you connect this wire to. All of the stop lamps are on the same circuit.

The converter will then have only one wire for LEFT turn and stop (usually YELLOW) this is the wire that needs to go to your trailer connector for left turn and stop.
The RIGHT turn and stop will most likely be GREEN coming out of the converter.

Posted on Sep 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Shrysler 300m Insturment cluster dose not work


Have you checked wiring harnesses that attach to cluster ?
Also check main ground wires that are part of the cluster.

Nov 05, 2016 | 1999 Chrysler 300M

1 Answer

I need to see a diagram on how to replace headlight harness connector that is located inside the headlight on 2004 chrysler crossfire


Pull the rubber dust cover back you will see the electrical wires going to the bulb you can pull the old connector off from there it is not inside the housing, the bulb is held in by a small spring clip at the back of the bulb socket.

Sep 06, 2014 | 2004 Chrysler Crossfire

1 Answer

I have a 2004 Hyundai Elantra and am trying to install a stereo but dont know what the wiring diagram is..any help?


Personally owning this car and installing several Hyundai stereo's, I would purchase a wiring harness kit from car audio shop or electronics retailer. The wire harness has a plug that connects to the cars wiring harness. This wiring harness kit will also list the wires to connect your new aftermarket radio to the harness. I would also recommend using crimped **** connectors to attach the two harnesses together.

Feb 24, 2010 | 2004 Hyundai Elantra

1 Answer

How do you remove and replace the headlight bulb in a chrysler 300M


Find the wiring connector on the back of the headlight (under the hood.) Unplug the connector and remove the lock ring around it (turn it like a jar lid a fraction of a turn.) Wiggle the bulb out - it is held in with a rubber ring. Secure the new one in place in the same position - it won't go in the wrong way. Reinstall the lock ring and wire connector.

Jan 16, 2010 | 2006 Chrysler 300M

1 Answer

Installing electronic trailer brake for 2005 dodge ram 150. How to? I have a Reese Brakeman Compact to install. It has four wires (blue, black, red and white) coming out of it, but how do i figure our...


Get the Dodge harness adaptor. Typically about $15 at most auto supply places that carries towing stuff, possibly at an RV center too.
The adaptor will connect to a white plug under your dash, if you have the towing package installed from the factory.
Mine (a '97) was taped to the mega connector just to the right of the e-brake pedal... The package came with instructions on where to find it but no pictures so I had to dig a bit up under there!
If you do not have the towing package, you will be best served doing as the instructions that came with the controller say OR downloading instructions from the Reese website.

Jul 17, 2009 | 2004 Dodge Ram 2500

3 Answers

I need a free owners manual for a 2000 chrysler 300M


There will be a few minor differences between the 2000 and 2004, but for the most part, you can use the 2004 manual as a reference. Since it is illustrated, you can confirm visually when you are taking on repairs. I have owned a 2000 300m for several years. Might I recommend you visit 300mclub.org? I am a member there and have learned a ton about 300m's.

Apr 19, 2009 | 2000 Chrysler 300M

1 Answer

Changing headlight 300m


lift the hood. the light are down behind the light assembly. simply turn large black ring and it will come out. be carefull not to touch the glass on the new one. oil from your skin will cause it to prematurely fail.

Mar 11, 2009 | 2004 Chrysler 300M

1 Answer

300m 2004


i hope this helps. tnx!

Oct 07, 2008 | 2004 Chrysler 300M

1 Answer

Headlights high beam light inside stay on


Do you have an aftermarket hitch?? I have seen a lot of issues with people having U-HAUL hitch installed with the convertor box. Whell, when the convertor box is installed, u-haul uses scotch locks, which after a while causes all kinds of electrical issues. including head light issues. Also check the convertor box. It may be faulty. Nissan make a very nice harness for the truck. no splicing needed. There is a single connector behind the bumper on passenger side. Get harness. That is if you have the u-haul convertor. If you dont, I would be looking at the head lamp switch.

Jun 26, 2008 | 2001 Nissan Xterra

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...