Question about Cars & Trucks

1 Answer

Took all my fueal injectors out of motor ..looked at the hole wear thay came out of the block.. thay wear all dry except one thats near the end of the fuel rail near the regulator ...why would that be and im guessing thats why in getting to muck gas and it spudders an smell gas out the exzost... but why does it do this

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    Visited the website for 3 consecutive days.


    An expert that hasĀ over 10 points.

  • Contributor
  • 15 Answers

What kind of car is this? you should check vacuum leaks with gauged tool and check Fuel pressure

Posted on Dec 07, 2012

  • roland Dec 07, 2012

    it a 96 pontiac grand am 2.4

  • roland Dec 07, 2012

    i changed coil packs.. plugs.. plug boots position sensor runs but spudders like one cyl aint fireing gas smell out exzost and check engin light flashes



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 202 Answers

SOURCE: Fuel injectors leak at fuel rail

Get some new O-rings, and this time put oil on them before you insert them into the fuel rail. The regulator is alright.The problem is that the o-rings can roll up, or twist when push em in dry. Had this problem once, easy fix, but was frustrating.

Posted on Mar 30, 2009

  • 58 Answers

SOURCE: fuel leaking at or near injector rail

if all the injestors on the rail came out i would replace the all

Posted on Apr 12, 2009

  • 11 Answers

SOURCE: my 97 olds achieva wont start. i took the

hi there the problem sounds like timing have u put the leads on the injectors the right order or the leads on the plugs the rong order

Posted on Apr 26, 2009

  • 3433 Answers

SOURCE: I'm smelling gas fumes outside my car. I can

vapor recovery system, should clear itself, some liquid fuel got into the vapor system. Avoid topping off the fuel tank.

Posted on Jul 11, 2009

  • 145 Answers

SOURCE: 93 Buick Skylark 3.3: WON'T starter,

check the wires of crankshaft position sensor and if OK change the sensor.
i seen this problem several times on the same car.

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

02 Chrysler van 3.8 came in with blown head gasket and a check engine light for misfire no1 cyl. Installed new head gasket new rebuilt heads plugs wires started up still misfire 1 and now 4

erratic compression indicates a cam lobe problem or cam follower problem
with that many miles on it , the cam shaft will have wear on it but the rest of the motor will have considerable wear including possible ring problems on the numbered pistons
If the body is rust free consider a new -out of the box engine as a cheap plug to stop the repair waste of money

May 06, 2017 | Chrysler Cars & Trucks

1 Answer

Clogged fuel injectors

If fuel filter was full of rust or anything except fuel, some may have moved further down to the injectors and be blocking them. They have very small holes and any 'hard' dirt or grit can block them.
You can try adding a whole bottle of RedX fuel additive cleaner to the gas tank and running with it, it may clean some of the gunge out of the injectors. Next step is too have the injectors removed and tested for efficiency, they will probably have to be replaced. Buying and fitting used injectors would be cheaper than testing yours. In any case, replace the fuel filters to stop any other grit in them moving to the injectors.

Dec 21, 2013 | Cars & Trucks

1 Answer

Near side brake juddering

The wheel wobble could be balance on road wheel,check n/s track rod end for wear this could be why the tyre is wearing.If you change track rod end get it re-tracked and the front wheels balanced...Good-luck...

Jan 06, 2013 | Cars & Trucks

1 Answer

2004 dodge 1500 4.7L 150,000 miles. took it to autozone to hook it to the computer and said misfire. what does that mean sparkplugs? also temp guage (inside) says overheating but when touched vy hand is...

Hi, my name is Shaun. i will try to help you out with your problem. Spark plugs and wires are a primary cause for an engine to misfire. I would definitely look into this first. From there it could be a distributor problem or coil pack, if your ignition is distributorless. Also try running some injector cleaner through you engine in case you have a clogged injector. Your temp. gauge problem is most likely a malfunctioning coolant temp. sending unit. This is usually located on the block very near your thermostat housing. Follow your upper radiator hose back to the engine to find the thermostat housing. Then look for a sensor that screws into the side of the block in that area of the motor. This is very easy to change yourself. Simply unplug the wiring harness, unscrew it and screw the new one in. But don't attempt this while the engine is hot. The coolant will be under pressure and can burn you severely. In fact, here is a picture I found that may help guide you to the sensor. Hope it is easy for you to decipher. The clicking noise may just be the result of a dry start or a sticking lifter. if it goes away after a second or two, I wouldn't worry much about it. Hope this helps. Good luck and have a great day!0996b43f80231101.jpg

Jun 21, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

My shogun sport will judder every so often when travelling just had new block but runs as though fuel starvation every so often new fuel filter fitted could it be the injectors need cleaning thanks.

Fuel injectors should not need cleaning because gas is so clean already these days.My tips about gas has some good info about that.Fuel starvation usually results in backfire.Are you getting that?I would think about the fuel pump.First I would inspect the spark plugs to ensure good spark.If you pull off a plug,it should look a little oily around/near the threads.If they look kind of dry and a rusty type color,it needs replacing.Be careful removing the plug wires,I always get one stuck on the plug and break off the contacter.Hold the plug against the engine block away from the hole and have someone turn over to start real quick.You should see spark.If not at first,try once or twice more.If those check fine,I would think about the fuel pump.You can also call a shop to get a free opinion.If 1 doesn't,hang up and try another.Someone is always willing to give a free opinion to attract business.I do it when necessary.Good luck! Greg

Aug 11, 2010 | 2004 Mitsubishi Montero Sport

2 Answers

How do I remove the back three sparkplugs on 3.1 cutless

There is a tool for it but you can do it lots of ways. First remove the two upper motor mounts that go to the radiator support. Put the car in neutral. Now you have to roll the motor forward. The way i do this is with a tie down strap. If you have a tie down strap hook one end to the engine, one of the lift holes is great, and hook the other end around the front bumper and hook it in a frame hole. Tighten the tie down strap and it will roll the motor forward and hold it there to give you the room you need. If you don't have a strap then you can use a pry bar to roll it forward they wedge a wood block between the alternator and the firewall to hold the engine forward.

Apr 11, 2010 | 1994 Oldsmobile Cutlass Supreme

2 Answers

98 Grand Cherokee blower fan works sparatically on all settings except low

chrysler blower motors pull alot of amps replace motor and resistor card

Aug 25, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2002 GMC 5.3 odd injectors don't fire . Random misfires. Took to a shop and they told me that the intake manifold gaskets needed replacing. Replaced them, also replaced fuel filter,plugs, plug wires and...

the intake manifold on them motor where cast bad and lots of them end up getting little tiny holes in the i have change lots of them for that prob also fuel regulaters leaking

Aug 18, 2009 | 2002 GMC Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides