Question about 2002 Oldsmobile Intrigue

1 Answer

How do you remove door pins - 2002 Oldsmobile Intrigue

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Take a flat head screw driver place at top of door pin tap upward with a hammer or take a small phillip screw driver place at bottom of door pin and tap out with a hammer.

Posted on Dec 06, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door bushings


The only door bushings I am aware of are the ones on the hinge pins. Correct? If not, please clarify what you mean.
New pins come with new bushings, and the hinges are welded on so the pins are pretty much the only items replaceable. Not a fun job - because of the door stop springs you will need a spring compressor, and you will also need a special tool to drive out the old pins. However, both are available from a parts store or Amazon.
Just open the door and support it from the bottom, and then go for it, one pin at a time - for the upper pin, compress and remove the small spring, drive out the old pin, drive in the new pin and put the spring back. No spring on the bottom hinge - just replace the pin.

Apr 02, 2014 | 2000 GMC Jimmy

1 Answer

How do I replace the long screw that holds the door up on the door hinges,on a '97 gmc Sonoma?


I have done a 100 of these.

The hardest part is going to be to reinstall the spring on the lower hinge arm. this is not a screw but rather a pin.
There are two hinges that hold the door to body.
when the upper and lower pins are removed the door will come away from body, it is important that before you remove the pins you take a look at the hinges.
Pay close att. to the way the hinges sit inside each other and the way the pins go in. see if they go from top to bottom or from bottom to top. also note where the copper bushings sit in hinges. each hinge has one pin and two copper bushings top go into hinge.
Over time the pins and bushings wear out ,making door hard to open and close. When the pins and bushings get so bad that the bushing is worn out and then the pins are now wearing into the hinge hole itself then this get tricky. if hinge hole is egg shaped the new bushings will not last. the door will hang again in a few weeks. this is where is get costly, the hinges now need replacing. i have gotten good at welding the holes and filing them back to shape but this takes skill or hole will be wrong and bushing will not fit or line up.

Here is a youtube video to help you.
Take note. put jack stands under door with cloth to avoid scratching door.this is to hold door when pins are removed. have somone help you, they will hold door on stands. the wires will still run through door, pull door away from body a little to allow room to work.remove the spring, it will fall out as you remove pins, remove old bushings, clean hinge area and holes,next install new bushings, apply lube to holes for pins and on bushings, slide door back on frame hinges and install pins, next slide lock washers on pins to hold pins. last is the spring. you will need a spring tool, you may rent one at auto parts store. hope this helps good day.

Feb 26, 2012 | 1997 GMC Sonoma

1 Answer

We need to replace drivers door on 1987 chevy s10 and can find only 1 bolt. What all needs removed to replace door?


the door henges are welded on the s10 you will need to remove the henge pins in order to remove the door, get some help! it will take 2 of you to get the door off and a floor jack helps a lot. you can get a tool called a pin popper and i recomend you do it makes the job much eazer, and the tool kit comes with the procdeger to remove the pins, when reinstalling the door replace the pins and bushings they come as a kit and can be bought at almost any auto parts store......good luck

Jul 06, 2011 | Chevrolet S 10 Cars & Trucks

2 Answers

Removing drivers side door panel ( inside panel )


Explorer/Mountaineer and 1993-99 Ranger
See Figures 1 and 2
  1. Open the window.
  2. Unscrew the door lock knob.
  3. On Explorer/Mountaineer, remove the 2 screws retaining the trim panel located above the door handle.
  4. On Ranger, remove the two screws in the armrest and remove it.
zjlimited_442.jpg

Fig. 1: Exploded view of the front door trim panel

zjlimited_443.jpg

Fig. 2: Exploded view of the Explorer and Mountaineer 4-door rear door trim panel

  1. If equipped with manual window crank handles, pull off the handle cover, then remove the attaching screw.
  2. Remove the trim cup behind (Explorer/Mountaineer) or around (Ranger) the door handle using a small prying tool. Retention nibs will flex for ease of removal.
  1. If equipped with power accessories, use the notch at the lower end of the plate and pry the plate off. Remove the plate from the trim panel and pull the wiring harness from behind the panel. Disconnect the harness from the switches.
  2. Remove any retaining screws uncovered by the removed trim pieces.
  3. Using a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
  4. Lift slightly to disengage the panel from the flange at the top of the door
  1. Disconnect the door courtesy lamp and remove the panel completely. Replace any damaged or bent attaching clips.
  2. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

Jan 10, 2011 | 1998 Ford Explorer

1 Answer

I need to replace side mirror on the passenger side,but not sure how to remove door panal to getto the plug


First roll down the window and remove the inside mirror cover the remove the push pins in the back of the door panel ( push the center in to the 1st click then remove the pin from the door panel . With the pin out of the door panel push the center pin back out of the push pin retainer so it will be ready to go back in)Then remove the screw cover behind the door pull (just pops out) remove the 2 screws . Use a door tirm tool to release the push pin retainers that hold the trim to the door and lift the door panel up and off the top edge of the door . disconnect the elec connectors.

Feb 23, 2010 | 2006 Chevrolet Malibu

1 Answer

Need to remove door panels to fix power windows and replace with no damage.


Door Panel
  1. Open the window.
  2. Unscrew the door lock knob.
  3. On Explorer/Mountaineer, remove the 2 screws retaining the trim panel located above the door handle.
  4. On Ranger, remove the two screws in the armrest and remove it.
a62714c.gif
Exploded view of the front door trim panel

5. If equipped with manual window crank handles, pull off the handle cover, then remove the attaching screw.
6. Remove the trim cup behind (Explorer/Mountaineer) or around (Ranger) the door handle using a small prying tool. Retention nibs will flex for ease of removal.
7. If equipped with power accessories, use the notch at the lower end of the plate and pry the plate off. Remove the plate from the trim panel and pull the wiring harness from behind the panel. Disconnect the harness from the switches.
8. Remove any retaining screws uncovered by the removed trim pieces.
9. Using a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
10. Lift slightly to disengage the panel from the flange at the top of the door.

41f9639.gif
... and remove it, then remove any uncovered screws


560e1b6.gif
Pry out the trim panel-to-door frame retaining clips, then lift up and pull the panel free

  1. Disconnect the door courtesy lamp and remove the panel completely. Replace any damaged or bent attaching clips.
  2. Installation is the reverse of removal.

Oct 31, 2009 | 1992 Ford Explorer

1 Answer

I need to replace the door hinge pin and bushing on a 1992 ford ranger,do I remove the door and how do I remove the pin?


yes you have to remove the door ... the pin have a C washer lock at the bottom. electircal wires are to be unpluged from inside the door or at the driver kick panel

Jul 26, 2009 | 1992 Ford Ranger

2 Answers

Pin for driver side door bottom hinge pin seems to have lost the bottom part of the pin, what is the easiest way to replace the pin?


door pins are available at dealer and part store

to change you have to remove the door from truck and change the pins

Jul 09, 2009 | 2002 Chevrolet Blazer

1 Answer

How do i get the door panel of f-150 off to replace handle 1994 pick-up


  1. Remove the armrest pad retaining screw.
  2. Remove the retaining screw and washer from the trim panel upper corner.
  3. Remove the door handle screw and pull off the handle.
  4. If equipped with manual windows, remove the window regulator handle screw and pull off the handle and washer. On vehicles with power windows, remove the power window switch housing.
  5. If equipped with manual door locks, remove the door lock control. On vehicles with power door locks, remove the power door lock switch housing.
  6. On models with electric outside rear view mirrors, remove the power mirror switch housing.
  7. Remove the retaining screw and washer from the trim panel lower corner.
  8. Using a special door trim panel removal tool or a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
  9. Installation is the reverse of removal.
Please don't forget to rate.

I'll get the pics here in a sec....takes a little bit to load.

May 13, 2009 | 1994 Ford F150 Styleside Supercab

3 Answers

Remove jeep door


You just need to use a small drift pin punch to push the door pins out. Use a small drift pin punch and a small hammer to drive the pin up and out from the bottom. It is just stuck in the hole.

Mar 17, 2009 | 2003 Jeep Wrangler

Not finding what you are looking for?
2002 Oldsmobile Intrigue Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...