SOURCE: reprogram fob key 2005 gododge durango
get the key code and take it to the dealership to have it rekeyed
SOURCE: reprogram key fob
Here is a quick HowTo on programming your own keyless entry:
1) Turn ignition to OFF.
2) Locate the Data Link Connector, its a black 16 pin connecter that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
3) Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
4) Close all of your doors.
5) Turn the key to ACC then back off. The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
6) Push a button on your key fob, doesn't matter which button.
7) If you have 2 key fobs, then press a button on the 2nd fob within 1 minute of pressing a button on the 1st fob. Both must be programmed at the same time. If you only have 1 fob then press a button 2 more times to signal that you only have one.
8) The doors will lock/unlock to signal the codes were received.
9) Remove the jumper wire from the data connector.
10) your done
SOURCE: reprogram 2005 Dodge Durango key fob
Go to the dealer. It is the only way, they have to use a computer. Changing the battery doesn't make it lose it's program though. You most likely broke the battery hold down. This is the most common thing I see at my shop. If the key still starts the vehicle, you now have a bad key fob. If not, you may be able to get it reprogrammed.
SOURCE: reprogram 2005 dodge durango key fob
Daimier Chrysler North American Remote Keyless Entry Programming procedures
Program Method A (Customer Program Method)
1. Press (LOCK) button 5 times at 2 second Intervals to resynchronize
transmitter, Attempt to function transmitter, If working as designed discontinue
programming.
2. Turn ignition to run position, (Allow Ignition chimes
to stop).
3. Using any original (working )transmitter, press the [UNLOCK]
button for 4 to 10 seconds.
4. Within the specified 4 to l0 seconds, continue pressing
the [UNLOCK] button and press the [PANIC] button for 1 second and release both
buttons (AN/DN release either button first). A chime will sound to indicate
that the transmitter programming mode has been entered (allow 3 seconds for
chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for
1 second and release (a short chime will sound for AN/DN).
6. Press and release any button an the same transmitter
and a chime will sound after successfully programming the transmitter (locks
will cycle for AN/DN).
NOTE.- (FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP #6 FOR THE FIRST TRANSMITTER
PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.
7. Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OF:F position. Transmitter programming
mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter
programming must be completed within time specified).
SOURCE: How to program a used
Hi,
If this is an used FOB,you will need to take it back to the dealer as the only way to program
the fob is with a scan tool. They should do it for free any way as they
lost the progra.
Procedure to program NEW FOB :-
Programming The Remote Keyless Entry (RKE) Module
1. Unlock the vehicle and disarm the Vehicle Theft Security System.
2. Insert ignition key into the ignition switch.
3. Turn the ignition switch to RUN position without starting the engine.
4. Using a functional key fob transmitter, press and hold the UNLOCK button for a minimum five seconds (maximum ten seconds).
5. While still holding the UNLOCK button, and before ten seconds
passes, press the PANIC button and release both at the same time. A
single chime will sound to verify that the RKE module is set to receive
the new Vehicle Access Code(s).
6. Within 30 seconds of the
chime, press and release the "LOCK" and "UNLOCK" buttons on the
transmitter at the same time. Then press and release any one of the
buttons. The BCM will sound an abbreviated chime to acknowledge that
the programming of the transmitter has been completed and was
successful.
7. Repeat step 6 for all transmitters that will be used with this vehicle, up to 4 total.
8. Programming mode will last for 30 seconds. To get out of programming
mode sooner, turn the ignition OFF. A single chime will sound to
verify that the RKE module will no longer accept additional Vehicle
Access Code(s).
9. When Vehicle Access Code(s) programming is
complete, turn the ignition switch to the OFF position and verify RKE
system operation using each key fob.
Let me know,if needed further assistance.
Kindly accept my solution.
Thanks for using ' Fixya ' and have a nice day!!
If
the remote s faulty then key fob will not get programmed.
Insert
the key in ignition. Turn the key to on position, and cycle the key three times
off-on-off-on-off-on. Then with the key fob remote select your remote and then
try to operate the vehicle with remote.
These
are just the basic procedure, but sometimes it will not help.
On
that case dealer is the only option.
---------
There
are few much related troubleshooting links mentioned below for remote key fob reprogramming.
I suggest you to go through the list and click the link below to go through its
details and procedure: -------
http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html
-------------
http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html
----------
-----------
http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html
-------------
http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html
----------
http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html
----------
http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------
http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------
http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html
----------------
http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html
-------------
http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html
---------------
http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html
-----------
http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html
------------
-----------
http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html
-------------
-----------
-----------
http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These
details will help.
Thanks.
1,410 views
Usually answered in minutes!
×