Question about 1992 Ford F250
While driving to work my 1992 F250 "hiccupped" 3 times then died. We now don't have any spark to the distributor and the fuel pump won't kick in. We were told it may be the EEC power-up relay but haven't had any luck locating it in the truck. We have looked in the fuse/relay compartment and it's not there. Any help would be greatly appreciated.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
if you replaced fuel pump i would look at backward wiring when replaced and i would start at the source of work if your vehicle was working fine before replacement then 9 out of 10 it will be your fuel pump wireing
sometimes when putting wireing back together the connectors have the missing clip and in turn you can turn the wireing in both directions now where positive is touching the ground on both sides of connector kris kross problem check your work this is crucial use a test light to find the right wires where they go
Posted on May 26, 2008
SOURCE: 1992 ford ranger
If this speratic problem seams to happen most when it's raining or damp, it is a shorting master contol that is to blame. The master control mother board is located on the firewall. Over time, the moisture seal on the cover fails and the motherboard gets damp and meny false signals are sent. This can even happen if the truck is off and key is not in the ignition (this mother board will alwas have power going to it as long as the battery is connected). A cheap way to check this is to remove the cover, put a plastic grocery bag over the mother board and use an small elastic band to close the open end, allow the wires connected to the mother board to go out the open end. If this solves the problem, replace the seals on the master control cover. Care should be taken as if there is ANY corrossion on the mother board, it will need to be replaced.
Posted on Oct 28, 2008
good old ford lol, try looking at the crank sensor its located at the front of the engine tucked in right hand side of exhaust manifold and gearbox, two pin plug, i have also known these to have no end of faults with the fusebox.
easy to remove, and solder the connections inside they all suffer eventually, if your not to handy with cars i recommend taking to a auto electrician, easy if you know how. Good luck Davelee
Posted on Mar 24, 2009
I understand that there is a relay box under the hood with 3 relays. Which is which I don't know. However if you are blowing the fuse TO the ecc relay, then the relay must be bad. This relay controls the spark.
Posted on Jul 25, 2009
SOURCE: ford explorer eec relay
Try a new relay first. This may not be good news if that does not work. If you can find the EEC (computer) and unplug it, then replace the fuse-if it blows you have another cheaper part on the circuit thats bad.
If the fuse does not blow, then the EEC must be shorted.
If you have to replace the EEC you may find a kindly dealer with a cash-for-clunker sitting there to violate. Salvage yards have them, Ebay sells them. I have seen them at swap meets for $20. They are a high price part even rebuilt at Dealers or autoparts stores.
Posted on Aug 24, 2009
Tips for a great answer:
Sep 24, 2012 | Ford Ranger Cars & Trucks
Dec 20, 2011 | 1992 Ford F250
Sep 18, 2011 | 1982 Ford F 250
Oct 18, 2010 | 1991 Ford F250
Apr 29, 2009 | 1992 Ford F250
Mar 11, 2009 | 1992 Ford F250
73 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: