Question about Cars & Trucks

Open Question

Problem with 2001 kia sephia

How to replace the power steering belt

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1214 Answers

SOURCE: replacing the alternator belt on 2001 kia spectra

Then you don't take anything off. There will be a spring loaded idler that tensions the serpentine belt. Take a socket or long 12 point wrench and attach to the center bolt of the tensioner, then rotate the idler wheel away from the belt, take the belt off. Slowly release the spring tension of the idler.
The 2nd belt should be set up the same way.

Posted on Jan 23, 2009

Ad
usa784
  • 9 Answers

SOURCE: I need to rplace tke power steering hose on a 2000 kia sephia

we tried fixing the old power steering hose, finally just had it taken off and another made up by an auto shop, cost $65 to have one made. very easy to fix, just undo at each end. this is a pressure hose though so make sure and get the same kind made.

Posted on Apr 28, 2009

  • 1 Answer

SOURCE: Power Steering Pressure Hose

Simple. Remove bolt from pump. Remove 2 10mm bolts that anchor it to the frame. Then disconnect it where the 2 hoses meet just behind the alternator. Takes less than 3 minutes without air tools.

Posted on May 15, 2009

c17hydro
  • 2984 Answers

SOURCE: the power steering belt is broke on a kia sportage

I would replace it yourself....very simple to do! The belt is $13.00 Power Steering Pump Belt

  1. Disconnect the negative battery cable.
  2. Remove the A/C and alternator drive belts for access.
  3. Loosen mounting lock bolt (A) and mounting bolt (B).
  4. With tension released removed the belt.
To install:
  1. Properly route drive belt around the pulleys.
  2. Carefully pry on the power steering pump using a suitable lever. Adjust belt tension is 22 ft. lbs. (30 Nm) when measured at deflection point shown.
  3. Retighten bolts (A) and (B) to 31 ft. lbs. (42 Nm).
  4. Reinstall the A/C and alternator drive belts.
  5. Connect the negative battery cable.
a30e7b7.jpg

Posted on Oct 10, 2009

iambanshee74
  • 3489 Answers

SOURCE: Power steering fluid in the 96 Kia Sephia.

there should be a resevoir on the passenger side of the vehicle. black cap, yellow or white in color resevoir. add dexron/mercon IV or better.

Posted on Nov 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a power steering belt on a 2000 kia sephia


Loosen the vertical bolt on the tension bracket by turning left, then slide belt off pulleys when you have enough slack, use a tension guage to reinstall and tighten to proper tension.

Feb 23, 2015 | 2000 Kia Sephia

1 Answer

How do I replace the serpentine belt on a 1999 Kia Sephia?


1.8L Engine
  1. Using a belt tension gauge, measure the drive belt tension and compare with the following specifications:
    1. Alternator belt (new): 86-103 lbs. (383-461 N)
    2. Alternator belt (used): 68-86 lbs. (304-383 N)
    3. A/C compressor and power steering pump belt (new): 110-132 lbs (491-589 N)
    4. A/C compressor and power steering pump belt (used): 95-110 lbs. (422-491 N)

      zjlimited_1999.jpg
      Fig. Using a tension gauge to measure the alternator belt tension - 1.8L engines (click HERE for zoom)


  2. Using the deflection method, apply moderate pressure (about 22 lbs) halfway between the pulleys, and compare with the following specifications.
    1. Alternator belt (new): 0.31-0.35 in. (8-9mm)
    2. Alternator belt (used): 0.35-0.39 in. (9-10mm)
    3. A/C compressor and power steering pump belt (new): 0.31-0.35 in. (8-9mm)
    4. A/C compressor and power steering pump belt (used): 0.35-0.39 in. (9-10mm)
  3. If the specifications fall outside the ranges given, adjust the belt as follows:
    1. Loosen the alternator mounting bolt and adjusting bolt.
    2. Adjust the alternator to get the specified belt deflection.
    3. Tighten the bolts, then recheck the tension.

      zjlimited_2000.jpg
      Fig. Adjusting the alternator belt-1.8L engines

Hope helps.

Oct 09, 2011 | 1999 Kia Sephia

2 Answers

POWER STEERING WENT OUT, 2001 SEPHIA


check the fluid. if its fine then you probally need a rack and pinion. also check the belt that runs the pump.

Feb 05, 2010 | 2000 Kia Sephia

1 Answer

2001 Kia Sephia, steering box unit, grinding when wheel is turned


That sounds like a cv joint. It is right behind the tire on the end of the axle. It should have a rubber boot around it. I suspect the boot went bad causing you to lose the grease.

Jan 24, 2010 | 2001 Kia Sephia

1 Answer

Need help replacing apower steering belt in a 2000 kia sephia. step by step


for 20 bucks u can by a manuual at your local auto store that will give you step by step on changing power steering belt,also rite size renches,sockets,ext...

Dec 15, 2009 | 2000 Kia Sephia

2 Answers

Timing belt replacement for 2001 Kia Sephia


For California models recommended at 105,000 miles.Belt needs to be inspected at 60,000 and 90,000, miles and replace at 105,000 miles.
Except California replace at 60,000 miles. Note 1.8L engine is a interference engine, if timing belt goes bad will cause major internal engine damage.

Nov 16, 2009 | 2001 Kia Sephia

1 Answer

I need a new timming belt on a 01 kia sephia how do i change it


Hi there,

Below are the procedures to remove the timing belt...

1. Disconnect negative battery cable.

fd440e5.jpg
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt. 3. Remove P/S and/or A/C drive belt.

1d207cf.jpg

4. Loosen generator mounting bolts and adjusting bolt. 5. Remove generator bolts.


077a275.jpg

6. Remove water pump pulley.

2bc0452.jpg


7. Remove crankshaft pulley and timing belt guide plate.



8619b52.jpg


8. Remove upper and lower timing belt covers.


c250533.jpg


9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.


213d3a1.jpg




10. Check that "I" mark on intake camshaft pulley is aligned with mark on cylinder head cover and "E" mark on exhaust camshaft pulley is aligned with mark on cylinder head cover.


Do not move camshaft or crankshaft once timing marks have been correctly positioned.



a3188ba.jpg



11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.


12101a7.jpg

14. Remove timing belt.



Regards,
Jeep Brainy

Sep 20, 2009 | 2001 Kia Sephia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...