Question about Cars & Trucks

1 Answer

I have a manual 84 bronco ii, me and my friend just rebuilt the carb. as I was driving home, I was in 4th and lost power, started losing speed. I tried to downshift and it died. When I pulled over and tried ti start it it wouldn't even turn over. I finally get it started and it makes a horrible clanking noise from what sounds like the engin. I have no idea what it could be.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,109 Answers

It sounds like a engine failure.

Posted on Dec 06, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ilragatzzo78
  • 241 Answers

SOURCE: '97 Ford Ranger-Please Help!

IT LOOKS LIKE YOUR FUEL PUMP IS GOING BAD

Posted on May 29, 2008

  • 10 Answers

SOURCE: 84 Porsche 944,Stopped running while driving, will not turn over

check the timing belt. this auto is a valve bender.

Posted on Feb 15, 2009

  • 100 Answers

SOURCE: renault megane 1999 whirring noise from engine ,car wont start

sounds like your timing belt has snapped, allowing the engine to tutrn over but the belt is not turning the vales, hence no start

Posted on Feb 16, 2009

  • 6982 Answers

SOURCE: 91 buick regal 3.8L is making a loud clank noise in belt area

did you check all the pulleys for smooth operation and looseness? did you check that the crank pulley and damper are OK?

Posted on Jun 03, 2009

  • 753 Answers

SOURCE: engine died.won't start.

Sounds like your crank sensor is faulty.These engines are known for crank sensor and ingition control module problems

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984 Bronco ii


starter silanoid feeds power to the coil after start up giving 9 volts could be giving to much voltage check with volt meter while running

Aug 27, 2012 | 1984 Ford Bronco II

1 Answer

Can I tow a 1985 ford bronco II 4x4 with hubs and a 5 speed manual trans. without disconnecting the drive line


yes if you make sure the front hubs are disengaged(turn little hub releases in middle of the wheel,man trans is ok auto not ok you do need to remove the drive shaft of an auto not man

Oct 26, 2009 | 1985 Ford Bronco II

1 Answer

Why does my 1989 bronco II lose power after it gets warmed up? After taking off from a stop, I have to floor it to get it moving, & it is slow getting up to speed.


does it feel like it is running rough? a mis fire could cause this and if it does it when it warms up you could have a fuel riching mixture problem.

how does it feel>?

Oct 25, 2009 | 1989 Ford Bronco II

1 Answer

Drive belt configuration for 84 B II


Yours Maybe Missing But Ford Puts A Sticker On The Front Crossmember At The Radiator Somewhere Close To The Hood Latch It Shaws The Belt Routing For Your Vehicle's Engine Hope This Help's

Jul 16, 2009 | 1984 Ford Bronco II

1 Answer

84 ford bronco 2 209 leitter v 6


you will need tocheck choke/choke pull off also the egr could be malfunctioning

Feb 10, 2009 | 1987 Ford Bronco II

1 Answer

1988 Bronco II transmission pop out of 1st gear


there are dent and brass balls that are in your transmission and are used to hold the shifter into each gear when it starts poping out of that means that those dents and brass balls are worn down and i would suggest getting the transmission rebuilt.

Dec 16, 2008 | 1988 Ford Bronco II

2 Answers

'97 Ford Ranger-Please Help!


IT LOOKS LIKE YOUR FUEL PUMP IS GOING BAD

May 29, 2008 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...