Question about 2002 Hyundai XG350

Open Question

Replacing low beam bulb on hyundia xg350 - 2002 Hyundai XG350

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 53 Answers

SOURCE: 2006 sonata replacing low beam bulb?

there is a spring clip holding it in push the clip towards the head light then down this will release the bulb it is much easer to do with the lens removed

Posted on Oct 19, 2008

Ad
ghost4548
  • 776 Answers

SOURCE: Changing the headlights

This picture shows the rear side of the headlamp assembly. I've circled the access caps to the high & low beam bulbs (they just twist off (counter-clockwise) to access the bulbs. Depending on which engine is in your Tiburon, access is easier if you remove three 10mm mounting bolts to the headlamp assemblies and remove the entire headlamp assemblies (see illustration)
c173c7f.jpg You'll want to disconnect these two connectors .. then remember to reconnect them when you put the assemblies back on.

Hope this helps

Posted on May 31, 2009

greg_margo
  • 1959 Answers

SOURCE: I need to change the low beam headlight bulb

  1. Remove headlight mounting bolts and nut
  2. Remove assembly
  3. Install headlight assembly (with new bulb)
  4. Replace/tighten headlight mounting bolts and nut
e2ac826.gif


Posted on Oct 30, 2009

  • 7353 Answers

SOURCE: my passenger side low beam headlight is out. the

Check the fuse. There are seperate fuses for right and left. You dont mention if the high beam works for that side? If it does, the fuse is good. The GREEN wire at the bulb is the ground for the low beam. If that wire has power, then the ground is bad. If the high beam works, the hi'lo beam switch is good, and there is a problem between that headlight and the Engine Compartment Junction Block

Posted on Dec 16, 2009

  • 89 Answers

SOURCE: HOW TO CHANGE A LOW BEAM HEADLIGHT BULD IN A 2008

Open the hood and look on the back side of the head lights for the wires running to them. With the lights off turn the houseing to remove the bulb> when replaceing don not touch the bulb with bare skin the oils will burn it up or even catch a fire..

Posted on Oct 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No low beams on headlights. have high beams, but no low beams or dashlights


Under hood in a fuse box is a relay for the low beams also a fuse in the fuse box somewhere in dashboard for both headlights and dashlights

Mar 31, 2015 | 2005 Hyundai XG350 L

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

I replaced both H1 bulbs on my 2002 hyundai XG350 and the normal daytime lights work fine but when Itry to use the hi beams to flash another driver they don't respond although the blue light indicato


i think the problem is more likely to be a relay but yes it could be a fuse but which one is for the lights i honestly do not know but if no fuse layout then check the 10/15 amp fuese as its most likely to be one of these

Dec 06, 2011 | 2002 Hyundai XG350

1 Answer

Replacing headlights I have a blown low beam


to replace the headlights themselves, no. under the hood, find the headlight. where it connects to the headlight lamp, it should simply twist off and pull out. Then you must unclip the clip holding the light on. It sounds sort of confusing, but it's really easy! Let me know if you need a bit more clarification.

Jan 10, 2011 | 2002 Hyundai XG350

1 Answer

HOW TO CHANGE A LOW BEAM HEADLIGHT BULD IN A 2008 HYUNDIA SONATA


Open the hood and look on the back side of the head lights for the wires running to them. With the lights off turn the houseing to remove the bulb> when replaceing don not touch the bulb with bare skin the oils will burn it up or even catch a fire..

Oct 21, 2010 | 2008 Hyundai Sonata

1 Answer

I recently puchased blueish headlight bulbs for my 2006 Volvo S80. The original bulbs were 55W for both the low and high beams. i replaced the high beams with 100w blueish bulbs and they work fine. When...


i think im right in saying the low beam bulbs are twin filament(low and high beam in one)and the main/high beam are single filament(spotlights).

Aug 17, 2010 | 2006 Volvo S60

1 Answer

2002 XG 350. License plate bulb out. How do I pull bulb, wiring is too tight. Thanks Joe B


2002 HYUNDIA XL 350, LIC. PLATE BLUBS CAN NOT GET ASSEMBLY DOWN TO REPLACE BLUBS, DUE TO THE FACT THE WIRES ARE TOO SHORT TO PULL UNIT DOWN. ANYH IDEAS?

Oct 30, 2009 | 2002 Hyundai XG350

1 Answer

How to change front headlamp bulb? Low beam


  1. Open the hood.
  2. Remove Grille.
  3. Remove the 2 retainers on back of headlamp assembly and remove the headlamp from the sheet metal panel.
  4. Remove the access cover from the rear of the headlamp.
  5. Disconnect the electrical connector from the socket.
  6. Rotate the bulb and socket counter clockwise in order to remove the bulb and socket from the housing.
  7. Disconnect the electrical connector from the socket.
  8. Remove the bulb and socket from the headlamp.
Installation Procedure Important: • Replace a high beam bulb with another high beam bulb. The high beam bulb has a black socket. • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a grey socket.

Oct 14, 2009 | 2002 Chevrolet TrailBlazer

3 Answers

Directions for replacing fog lamp bulb on 2005 hyundai xg350


first start by popping the hood then removing the gray caps covering ether the low beam or high beam depending on witch your replacing these are located on the right front by the battery and left front by the windshield fluid reserve then undo the metal clamp securing the bulb then carefully remove the bulb keeping in mint to only attempt this after the bulb has cool because they get extremely hot and never touch the bulb if you plan on using then again after that disconnect the wire harness from the bulb then take your new bulb and it will plug right in.WARNING HID BULBS WILL NOT WORK OR CONNECT PROPERLY IF YOU DON'T HAVE A COMPLETE HID KIT.

Aug 12, 2009 | Hyundai Motor 2005 XG350

2 Answers

Low beams do not work, replaced turn signal switch but still no low beams. High beams work but no low. Please Help


its probally the bulb........alot of car headlights are DUAL element meaning one bulb has 2 little elements inside one for low beam one for high beam...............Most times the low beam burns out because its used more.....get it one bulb gives both high and low beams.......REPLACE bulb......if you don't know what kind go to auto part store, tell them the make of your car and they will give you the right one .....

May 09, 2009 | 1997 Ford Explorer AWD

Not finding what you are looking for?
2002 Hyundai XG350 Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...