Question about 2008 Dodge Avenger

Open Question

Code P2610 Malfunction light is now - scanned on computer and Code P2610 shows up 3 times

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Pontiac vibe 2006 is showing PO6006, PO6007 code does anyone ha be any idea what it means


P0606 , P0607 ! no such codes P06006 or P06007
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610
DTC P0606 Control Module Internal Performance
The DTC P0606 and P2610 set when the powertrain control module (PCM) has determined that the control module has an internal fault. The PCM performs continuous self checks of all internal circuits. There are 2 central processing units (CPU) within the control module. If the outputs from the two CPUs deviates from the standard level, a DTC P0606 sets. The control module has several internal clock or timer circuits. The DTC P2610 diagnostic monitors the internal timer circuit responsible for the ignition OFF operation of the evaporative emission (EVAP) system vacuum leak pump. If the there is an error in the control module timer, a DTC P2610 sets.

Feb 25, 2016 | 2006 Pontiac Vibe

2 Answers

What is code p2610


"DTC P2610 is set if an internal ECM problem is detected.
1.With ignition OFF, remove both ECM connectors.
2.Wait at least one minute.
3. Replace the connectors making sure to completely seat and lock them.
4.Turn the ignition ON with the engine OFF, and clear the stored codes.Verify the MIL light turns OFF, and stays OFF. If the MIL light does not turn OFF, repeat the clear code command until it the MIL light remains OFF.
5.Turn OFF the ignition and leave it OFF for at least one minute.
6.Turn the ignition back ON with engine OFF and observe that the DTC does not reset.
If the DTC P2610 is still set, repeat Steps 1 through 6 one additional time. If Steps 1 through 6 still do not correct the DTC P2610, verify there is constant battery voltage to ECM Connector C1- terminal 77. (circuit 440 / orange wire) If battery voltage is not present on Connector C1- terminal 77, troubleshoot and repair the circuit."

Oct 27, 2014 | Kia Sedona Cars & Trucks

1 Answer

P2610 code aveo 2009


the code means this ECM/PCM INTERNAL ENGINE OFF TIME PERFORMANCE

Jan 24, 2013 | 2005 Chevrolet Aveo

1 Answer

Hi, I have a Jaguar x-type 2.0 v6 2002, and i stalled it and quickly turned the engine back on, then the malfunction indicator lamp came on and won't go off. The car runs perfectly but this light...


Hi,
The light coming on is an indication of a malfunction in the engine management system.
The cars computer has now stored a malfunction code, turning on the light. A parts store as Auto Zone or a Jag dealer can scan the computer with a "code scanner". Many parts stores will do this for free.
The code scanner will give the reason why the light went on. This aids the mechanic of your choice in the repair.
You need to find a place to scan the computer. Although the car runs good the light is a warning that something is amiss.
Wayne

Aug 30, 2011 | 2002 Jaguar X-Type

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

1 Answer

Error Code PO 456


vacuum leak in the evaporative emission system hard one to solve without the vehicle but could be as easy as a loose or faulty fuel cap just think the fuel tank breaths as well

Jun 08, 2010 | 2006 Chrysler PT Cruiser

1 Answer

Check engine light is on; diagnostic code is P2610, What is that code and is it safe to drive my car until it is fixed?


p2610 is engine contro module or ecu the cars main computer for both fuel injection and ignition,Remove the large block connector going to the ecu and spray both with contact cleaner,should sort it.

Mar 04, 2010 | 2007 Toyota Corolla

4 Answers

How do you get the codes for a check eng. light on a 2002/3 chevy cavalier with out a reader?


dj,
AutoZone can retrieve the code(s) as a free service. Ask the tech for a print-out (free).
Let us know the codes and a summary of the print-out. We can assist from that point (free).

Nov 04, 2009 | 2002 Chevrolet Cavalier Coupe

2 Answers

Service engine light comes on 2006 pontiac blonnie, code 0440, what is it and how do I fix it


First thing to check is whether the gas cap is on tightly. If it is, the next would be to replace the gas cap. That solves 90% of these problems.

P0440 is a generic code for Evaporative Emission Control System Malfunction... pretty much for all makes. It takes 1 malfunction to create a pending DTC... at 2 consecutive malfunctions the MIL(Malfunction Indicator Light,Check Engine Light, etc.} Ok, after you fix it, it should take 3 trips to turn off the light, then 40 more to Remove the code from the computers memory

Oct 04, 2009 | 2005 Pontiac Bonneville

1 Answer

Malfunction indication


The Malfuntion Indicator Lamp (MIL) is being lit up by the vehicle's computer to indicate there is a problem with one of the vehicle's systems.Have the vehicle scanned,write down the code number and definition,and ask whoever scans it what's involved in repairing the malfunction,and what system it is in.Or come back in here with the code number and definition,and we can help you.

Jul 10, 2008 | 2003 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...