Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

Abs pump stays on

Which fuse to disable abs module

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 193 Answers

Need to unplug abs motor it self.

Posted on Dec 06, 2012

  • amarconi25
    amarconi25 Dec 10, 2012

    Thank you. That worked.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Disable ABS module


check all 4 fuses and see which is pulling power when off and pull that one or pull the relay

Sep 15, 2015 | Cars & Trucks

2 Answers

My ABS light stays on, Can the ABS system cause my rear wheels to heat up? (To hot to touch) 2003 ford explorer.


Remove the ABS fuse to disable the ABS system . The brakes will work as NORMAL brakes and you will now see if the rear brakes heat up. They more than likely will as the ABS would not have any effect on the brakes in normal running situations.
Suggest take the vehicle to a GOOD brake shop and get them to fix the problem

Apr 22, 2015 | Ford Cars & Trucks

1 Answer

AWD disabled, why


Wheel sensor/bearing bad, wire by the bearing broken,ABS module bad, bad ground wire for the ABS pump, ABS pump bad, The actuator/switch in the rear differential is bad, the wire for the rear switch is broken, the clutches in the rear differential are worn out. No oil in the rear differential (which trashes out the differential). And the fuses could be blown. I think I have covered all of it. From older ones to newer ones.

Mar 27, 2015 | Cars & Trucks

1 Answer

How to disable abs on 2001 taurus


There is a 10amp fuse in the underdash fuse box that may disable the warning light. There is a 20amp and 40amp fuse in the fuse box by the battery that powers the ABS module.

Jun 05, 2013 | Cars & Trucks

1 Answer

AWD Disable light on 2001 Pontiac Aztec- how do I get if off?


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 11, 2012 | 2001 Pontiac Aztek

1 Answer

Abs light stay on


When this light stays on it is warning you that the ABS control module has sensed a fault in the ABS brakes,it has turned on the light and disabled the system. What you must do now is have the ABS system module scanned for fault codes, then based on the code or codes the proper diagnostics are done and the problem parts replaced or wiring repaired.

Jun 27, 2012 | Nissan Tiida Cars & Trucks

1 Answer

2001 Suburban ABS motor staying on after ignition is off


what you have is a ABS module that has shorted out internally. you have to replace that module and then bleed the ABS pump AND the brakes at all wheels.

Aug 13, 2009 | 2003 Chevrolet Suburban 1500

2 Answers

2002 Suburban 1500 - ABS Light On


No doubt the control module is out, and it continue to operate when the ignition key is off due to a circuit fault. You can disable it easily by pulling the 60 amp fuse in the under hood fuse box (it is listed on the panel as ABS). Note that this disables the ABS braking feature and traction control, so be very careful when driving. The part can be purchased on the GM global parts site, about $600-$700 for the module. This will be the second time this has gone out for me and GM is not sympathetic, rather "pathetic", for a part to fail so often.

Apr 22, 2009 | 2002 Chevrolet Suburban 2500

3 Answers

Where is the abs control module located on a 02 chevy avalanche ?


THE EBCM IS BAD this is the electronic control module that is on abs pump. you can replace seperate I think it is around 500 for part

Dec 30, 2008 | 2002 Chevrolet Avalanche

2 Answers

ABS Pump wont shut off


go to www.modulemasters.com

The dealer will charge you $1300 - $2000. Contact Module Masters. They are great to deal with. You have to ship it to Moscow, Idaho. It cost me about $15 to ship it (with box, packing, and insurance at a UPS store). They charged me $130 to rebuild it and gave me a 5 year warranty. It cost $8 to ship it back. To in total, it cost me $153....totally turn-key.

Jun 30, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...