Question about 2002 Mazda Protege

Open Question

How do i remove the starter from a 2002 mazda protege?

How do i take off the starter from a 2002 mazda protege?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: 2002 Mazda Protege horn location

Their are usually in back of grille or on the underside of rails. you will need to take off the front bumper to get access.

Posted on Jan 24, 2009

  • 36 Answers

SOURCE: Timing Belt on 2002 Mazda Protege

every 90,000 to 100,000miles and yes it is strongly recomended to replace the water pump with it

Posted on Apr 02, 2009

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

  • 32 Answers

SOURCE: obd2 code p0300 on mazda protege 2002

Just had one of these with a maxima, the code is multiple random misfire, when a misfire occurs, to start is do the basics, replace the plugs, check fuel pressure, clean throttle body, and coolant is topped up. also I have seen if the O2 sensor is not working correctly is can cause a misfire, you will need a scan tool to look at what the O2 sensor is doing, o rby back probing the sensor (don't damage the O2 sensor wires). If it wires replace them as well, if it has coils they usually dont give that code if one fails, it will pinpoint that a certain coil if one fals.

Posted on Oct 02, 2009

  • 2 Answers

SOURCE: Where is the starter located

Your started is located on the back of the engine closest to the drivers side, under the air intake, if you remove your breather tube, that goes from your air box to the throttle body, you should be able to see it, It would be wise to safely support the vehicle, (or use a lift if you know someone who has access to one) as you may find it easier to do some things from the top and some other things from the bottom. Be sure you disconnect battery negative before you start the removal and clean all wire leads/connectors before installing the new one.

Posted on Oct 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on the 2002 Protege


Starters are usually found near the transmission or not far away from it. Check the engine bay around near your transmission and it should be connected to the side of your gearbox or connected to the flywheel. I hope this helps.

Sep 04, 2012 | 2002 Mazda Protege

1 Answer

My 2002 mazda protege lx refuses to start. The battery is fine, but the engine/stater makes no sound or attempt to start. What is the problem?Could it be a relay,the starter?


If your battery is known to be fine then you probably have a bad starter. You can pull it and take it to autozone and they will test it for free before you buy a new one.

Feb 17, 2012 | 2002 Mazda Protege

3 Answers

2002 mazda protege 5 will not start - will not turn over, starter is fine, battery is new, power is going to the starter, everything is clean, is in park or neutral, no clicking sound at all, fuses are...


Help please....I have Mazda Protege 2002...the car was driving good..and suddenly the car didn't start at all i changed the starter the battery is fine because when i start the car the lights comes on and the radio works. I don't know what is the problem is...when i start the car it makes noise of tik tik. Please help me????

Oct 05, 2009 | 2002 Mazda Protege

1 Answer

Where is the computer in2002 mazda protege es


Generally, the PCM (computer) is located under the passenger-side floor slope, under a metal frame. You may want to remove the passenger-side kick plate plastic and peel back some of the carpet to revel it.

I hope this helps! :)

Sep 01, 2009 | 2002 Mazda Protege

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

1 Answer

How to replace the serpentine belt of protege 5 2002, also need the routing diagram


Posted by Asker under 1997 Mazda Protege for their 2002 Mazda Protege 5.
Both are included Below

Click on the following free direct Link. It has the Belt Diagrams for the 1997 Mazda Protege with either the 1.5L DOHC In-Line 4-Cylinder or 1.8L DOHC In-Line 4-Cylinder Engines; along with various engine options (AC/No AC, etc.). Included are Instrucional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/1997/make/mazda/model/protege/1997_mazda_protege_drive_belt_routing_diagram.htm

Click on the following free direct Link. It has the Belt Diagrams for your 2002 Mazda Protege 5 2.0L DOHC In-Line 4-Cylinder Engine; along with various engine options (AC/No AC, etc.). Included are Instructional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/2002/make/mazda/model/protege5/2002_mazda_protege5_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 13, 2009 | 1997 Mazda Protege

2 Answers

Where is the blower motor resistor on a 2002 mazda protege?


just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Jan 31, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...