Question about 1985 Chevrolet Sportvan G20

Open Question

Install wiper motor G-20 Chevy Van - 1985 Chevrolet Sportvan G20

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
atye
  • 39 Answers

SOURCE: Can you please give me

This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



Posted on May 04, 2011

Ad
  • 3 Answers

SOURCE: wiper motor install problem 95 chevy van

remove the the arms and realign them

Posted on Feb 21, 2009

  • 312 Answers

SOURCE: trying to find location of wiper motor relay on a

if you can see your wiper motor, there is a black panel were the wires hook up to it, remove the three torx head screws unplug and pull out the wiper module. thats your relay and they are replaced a bunch, the've had a lot of problems with these modules.

Posted on Jan 11, 2010

jerroldwsmit
  • 6 Answers

SOURCE: We're replacing the motor, gear box and plates to

The wiper linkage and blades should be in the neutral position, or where they would normally lie when in the "off" position. Hope this helps. Remember to disconnect the battery while replacing electrical components.

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Whipers on 2005 gmc envoy stay on


Call a general motors dealer and have them run your vin. There was a recall on the wiper control circuit (I don't remember the year range). If there is no recall, that is still likely the problem.

May 01, 2016 | 2005 GMC Envoy Xl

1 Answer

Where is the wiper motor on 1993 chevy lumina van


wiper motor under cowl below windshield under the wiper arms.

Oct 31, 2012 | 1993 Chevrolet Lumina APV

1 Answer

Escort 55 1.8d van fuse 25 keeps blowing and cant start my van.circuit says wiper and washers and it wont let me install new fuse without blowing.i have work on monday !Help!


Unplug the wiper motor and replace the fuse. If it works the wiper motor is shorted out. It may also be the wiring rubbed thrue somewhere causing a short.

May 13, 2017 | Ford Escort Cars & Trucks

1 Answer

Can you please give me instructions on replacing the wiper motor pulse board module on my 95 Chevy Van G20?


This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



May 04, 2011 | Chevrolet G20 Cars & Trucks

1 Answer

We're replacing the motor, gear box and plates to


The wiper linkage and blades should be in the neutral position, or where they would normally lie when in the "off" position. Hope this helps. Remember to disconnect the battery while replacing electrical components.

May 12, 2010 | 1999 Chevrolet Venture

1 Answer

Trying to find location of wiper motor relay on a 1996 chevy astro van


if you can see your wiper motor, there is a black panel were the wires hook up to it, remove the three torx head screws unplug and pull out the wiper module. thats your relay and they are replaced a bunch, the've had a lot of problems with these modules.

Jan 09, 2010 | 1996 Chevrolet Astro

2 Answers

Rear wiper on chevy uplander does not work. fuses


i have a 2006 chevy uplander and i need to change the low beam headlamp how do i do it, also about a month after we had got the van the rear wiper stopped working i haven't checked the fuse yet, but is this a common problem for the uplander, and also the abs light stays on what should i do for that problem, and also when we drive it and then shut it off it does not want to turn on right away.

Oct 25, 2009 | 2006 Chevrolet Uplander

1 Answer

When turned off wipers arein the up position


This is a Common Problem On Chevy's. The easiest way is to get a New Wiper Motor and Install it. Very Easy to do and Cheaper than a Mechanic.

Jan 01, 2009 | 1999 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...