Question about Cars & Trucks

Open Question

Where is the oil pressure sending unit on chrysler 300 with the 2.7 engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 31 Answers

SOURCE: Can not find oil pressure sending unit on engine.

yes it will be on the lower part of the engine block. i believ on passenger side.

Posted on Jan 18, 2009

Ad
roedmondson
  • 68 Answers

SOURCE: Where is the oil pressure sending unit on 2004 Dodge stratus

Most likely the oil pressure switch may be damaged. This is a simple procedure. Change and observe the results

Posted on Jan 23, 2009

farroutideas
  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Posted on Mar 17, 2009

  • 1986 Answers

SOURCE: I keep getting a stop engine low oil pressure

Just wondering if you put in the correct amount of oil and tightened everything back up properly...

Posted on Sep 09, 2009

  • 1 Answer

SOURCE: where is the oil pressure sending unit on 2004 dodge stratus?

per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is oil pressure sending unit on 1990 chrysler new yorker located


The oil pressure switch and sending unit is located directly above the oil filter and next to the starter motor on the lower side of the engine block.
7_21_2016_5_24_52_pm.jpg

Jul 21, 2016 | Chrysler Cars & Trucks

1 Answer

Where is oil sending switch on Chrysler 300 2.7 location


I had a dodge intrepid with 2.7l engine the sending unit was close to the oil filter your should be the similar
25643820-4ykzrexlqaje1pigexqbewku-1-0.jpg

Apr 13, 2015 | Chrysler 300 Cars & Trucks

2 Answers

Change oil sending unit 04 tahoe


It is located on rear of engine back by the distributor use to be. see attached pic
25576498-orvua4poo00lqzajd5seke1u-5-0.gif

Mar 15, 2015 | 2004 Chevrolet Tahoe

1 Answer

Where is the oil pressure sending unit located on a 05 chyrsler 300 car


If the engine is the hemi it is behind and below the alternator.

Sep 06, 2014 | 2005 Chrysler 300

1 Answer

In my 2005 chrysler 300 the oillight keeps beeping and blinking,any ideas of whats going on?


The problem may be a leaking oil pressure sending unit. If the sender leaks it can fill the plug cavity with oil and cauce it to read improperly.If you decide to replace it get one from chrysler,I have gotten them in the aftermarket only to have the same concern.Once I installed one from dealer problem gone. ALSO . you may want to hook up an mechanical oil press gauge to pressure switch port to see what the pressure actually is to be sure you do not have low oil pressure.

Apr 13, 2011 | 2005 Chrysler 300

2 Answers

Where is the oil pressure sending unit located on a 1999 chrrsler cirrus


There are three engines that come with this car, there are two engines 2.0 and2.4 with the oil pressure switch located on the right front of the engine block, and then if it has the 2.5 engine then the oil pressure switch is located on the leftside of the engine block above the oil filter, good luck,.

Jan 01, 2011 | 1999 Chrysler 300M

1 Answer

Where is the oil pressure switch/sendor located?


Oil pressure can be checked at the sending unit passage with an externally mounted mechanical oil pressure gauge. To get accurate results from the test, make sure you follow the manufacturer's recommendations and compare your findings to specifications.
Testing the Oil Pressure Gauge
  • Test the gauge by grounding the wire that leads to the sending unit on the block.
  • When the wire is disconnected from the sending unit with the key switch on, the needle on the oil pressure gauge should be either all the way high or all the way low. Grounding the wire should make the needle move to the opposite side of the gauge from where it was before the wire was grounded. If the vehicle is equipped with an oil pressure light, touching the wire to ground and then removing the wire from ground should turn the light on and off.
  • If either happens, the gauge and wiring are good and the sending unit is at fault.
Testing Oil Pressure
Pressure can be tested by temporarily installing an oil pressure gauge in place of the sending unit. Before testing, look up the oil pressure specifications for your vehicle in the appropriate service manual.
  • Bring the engine up to operating temperature.
  • Now shut the engine off.
  • Locate the oil pressure sending unit; usually it is on the lower side of the engine block.
  • Disconnect the wire from the sending unit and use an open ended wrench to remove the sender. Using pliers can damage the unit.
f43-19.jpg An oil pressure sending unit is removed with a special socket. Courtesy of Chrysler Corporation.
  • Tighten the oil pressure test gauge into the hole in the block where the sender was removed.
f11-15_3184.gif Measuring oil pressure. Reprinted with permission.
  • Check the engine's oil level and fill, if required.
WARNING Be extremely careful when working near a running engine. Always wear safety goggles or glasses with side shields when working around moving machinery and be sure that your clothing is not loose.
  • Now turn the engine on and check the oil pressure on the gauge.
    • Watch as the engine warms to note any excessive drops due to temperature.
    • Make sure the engine speed is set to specifications for testing pressure.
    • If necessary, us a tachometer and adjust the engine idle speed.
  • Record the measured oil pressure, then turn off the engine.
  • Compare the test results with the manufacturer's specifications.
    • If the oil pressure is within specifications, this shows that the oil pressure sending unit may not be working correctly.
    • In many cases, replacing the oil sending unit will correct the problem.
  • After the test is complete, reinstall the oil pressure sending unit, start the engine, and confirm there are no leaks.

Nov 20, 2010 | 2002 Pontiac Bonneville

2 Answers

Oil light when idling


Have an oil pressure test done.
One of 4 things could possibly cause that.
Bad oil pressure sending unit.
just the oil sending unit.
weak oil pump.
low oil---check oil, see if it needs any.

Mar 12, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...