Question about Ford E-350

Open Question

Ford e350 braking steering pulls left

When braking the steering wheel pulls to the left. I did go through a big dip recently.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 156 Answers

SOURCE: squeaking when turning steering wheel

that would be your power steering. The fluid may be low.

Posted on Feb 23, 2009

  • 2 Answers

SOURCE: 1997 ford f250 steering problem

it could be the front axle u-joint binding up. i had the same problem, and that's what it was. i put greaseable u-joints on both sides.

Posted on Mar 19, 2009

warlock61
  • 659 Answers

SOURCE: Vibration in steering wheel

sounds like it could be the ball joints binding up

Posted on Mar 25, 2009

pippall
  • 1486 Answers

SOURCE: front-end clunk

bottom ball joints worn

Posted on May 30, 2009

  • 6982 Answers

SOURCE: What type of power steering fluid & capacity for 1985 ford e350?

On yours, you can use atf but power "steering fluid" works just as well.. steering fluid is used as a specific requirement on later vehicles and if you use it in the 85, you can use the leftover to top off anything you have that is newer. (can't do that with atf)

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wnen ever i apply brakes at a stop sign it vibrate ot when i turn left it vibrates


If it tries pull the steering wheel back and forth, it is brake rotors. If it just vibrates threw the body and steering, it is the right side wheel bearing.

May 14, 2016 | 2003 Ford F-350 Super Duty

1 Answer

1993 ford e350 cutaway


brake fluid hose towards the front wheels in the brake master is blocked.

Jun 20, 2013 | 2002 Ford E350

1 Answer

My 2003 f150 pulls to left when i initially apply brakes,then straightens out.I replaced both calipers,rotors and pads.bled air out of lines and problem still exist's.


Check the rubber bushings on the front suspension arms, especially the lower radius leading arms. When you brake the inertia of the car is thrown forward and the lower arms come under enormous strain. If the radius arm to body frame bushing has gone then the leading arm moves rearwards slightly and causes toe out on the front wheel. If one side is weaker than the other then the car steers/pulls in the direction of toe out. If these check out then look at the ball joints on the steering arms and the steering links. Use a pry bar and be quite forceful, its a big truck and there should be no movement.

Sep 16, 2011 | Ford F-150 Cars & Trucks

1 Answer

What could be causing my 1997 Ford E350 15 pass.club wagon to have excessive vibration when braking from highway speeds 60mph & up. Not so bad at slower speeds? Ford Tech said brakes were good. No...


ABS------ Anti Lock Brakes will cause a chatter if applied with a lot of weight pushing it. An E350 is a big rig.
Might ask your Ford Tech about that possibility.

Mar 05, 2010 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

I cannot find a fuse and braker location diagram for my 1998n ford e350 RV ?


Below and to the left of the steering wheel , by the brake pedal Remove the panel cover to access the fuses
this is according to the owners manual on the 1999 e350.
Now on my fathers rv though, there is a breaker/fuse box in the side of the table seats facing the walk way. Hope this helps.

Oct 27, 2009 | Ford E-350 Cars & Trucks

1 Answer

Need to replace 1997 e350 ford Ignition ,how can i


you dont have to remove the steering wheel on a most Ford car and trucks you insert the key turn to the on position and there is a small pin under the ignition switch that you push and it comes right out.you have to remove the steering wheel cover above and below the ignition switch.

Oct 04, 2009 | 1997 Ford F350 Crew Cab

1 Answer

Front-end clunk


bottom ball joints worn

May 30, 2009 | 2007 Ford Edge SEL Plus

1 Answer

No turn signals /breaklights/no powerlocks /e350 ford


turn signals and brake lamps go thru what ford calls a multi function switch.usually replaceable w/o removing steering wheel.pricey item...dealer only part. hazard lamps working?also part of the same switch.power locks not part of this switch.ground good on back of pdl switch?usually activated by grounding.hope this helps...

Mar 31, 2009 | 2002 Ford E350

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...