Question about Cars & Trucks

Open Question

I need a diagram for a 2 ton allied floor jack

Need to find out how to put a 2 ton allied floor jack together

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 6674 Answers

SOURCE: belt diagram 2004 5.7 liter engine dodge ram 1500 1/2 ton 4x4

click on this link, and scroll down to 5.7L

Posted on Dec 22, 2008

  • 986 Answers

SOURCE: Need diagram for hub assembley.

is it a stock or an after market hub?? Like Warn?

Posted on Sep 11, 2009

Testimonial: "warn, will be so thankful for your help"

  • 714 Answers

SOURCE: what ton hydraulic jack do i need for this car?

2 1/2 ton should be sufficent!

Posted on Mar 14, 2010

  • 5660 Answers

SOURCE: I have a 1959 CHEVY

To my knowledge the Headlight wiring, and Taillight wiring, follow the same schematics as the Impala, Belair, and Biscayne, of the '59 year,

Go to the bottom of the paragraph under the photo, and left-click on -
wiring diagram chevrolet 1959 V8 here

On the next page you can enlarge the wiring diagram one time, by left-clicking on it.


Posted on Sep 20, 2011

SOURCE: i need repair manual for michlen 3 1/2 floor jack

Can call manufacturer or check ebay

Posted on Nov 30, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace motor mounts on 2003 hyundai sonata

You really need the car on a lift or tall jack stands to do this. You will need a full set of hand tools, a good hydraulic floor jack, a set of Jack stands (AKA Safety Stands) and a 1.5 Ton bottle jack. Raise the front of the car as high as possible and unbolt the old mounts from the engine and engine cradle, then Carefully using the bottle jack (put a piece of wood on the plunger of the jack to avoid damage to the oil pan) raise the engine off the mounts and remove them, and reverse install new mounts, time about 2-3 hours to do the repair.

Oct 12, 2016 | Hyundai Motor 2003 Sonata

1 Answer

Fuel filter location?

most are in the gas tank.

Easy job if you have a floor jack, 2 floor stands and wrench.
Empty the gas tank, place jack centered on the gas tank jack up the car, put the floor stands in place to hold the car steady, disconnect the wiring go to the gas tank then remove the bolts (most cars only have 2 holding the tank braces, slowly lower the floor jack with the tank on it, remove the fuel pump slowly and carefully as not to have anything fall in the tank.

Dec 10, 2015 | Cars & Trucks

1 Answer

Put oil in allied 45426 floor jack

Remove the plug by inserting a flat head screwdriver underneath the plug and ... Most of the plugs will be made of rubber, and will be located on the top of the cylinder.
jack should be in down position when filling, so jack won't be over filled.
if jack is over filled it will blow filler plug off when lowered.

Jan 17, 2015 | Cars & Trucks

1 Answer

I need to replace rear axel on 2001 chevy silverado 1500

jack up the rear end high and place chassis rails on stands. Remove wheels . disconnect brake hose to the rear and use a hose pincher to stop brake fluid leaking out . Disconnect the hand brake cable at a convenient point ( probably at the rear of the transmission. Disconnect the drive shaft at the diff pinion and lay to one side . Place the jack under the diff housing centre and take a bit of weight. . If you have leaf springs --undo the "U" bolts around the housing . If coil springs undo the track rods by removing all the pivot bush bolts. Lower the diff housing down and pull out from under the car. Make any changes you have to, to the other diff housing before placing it on the jack and placing it under the car Reassembly is the reverse process of removal.. Bleed rear brakes on completion of the job.

Feb 20, 2014 | 2001 Chevrolet Silverado 1500

2 Answers

What size floor jack do I need for a 1987 toyota camry?

Any roll away floor jack from a autoparts store will be fine and strong enough

Mar 04, 2013 | 1987 Toyota Camry

1 Answer

How do I safely lift the front end of a 2000 chrysler concorde with a floor jack?

first, I would use jack on one side of car then put it on jack stands, then go and jack other side up and put it on jack stands, just the way I would do it

Oct 04, 2012 | 2000 Chrysler Concorde

1 Answer

Wiring diagram for distributor on 1984 chevy k10 1/2 ton

i need a diagram for putting back together a steering column in a 1984 chevy

Jan 15, 2012 | Cars & Trucks

1 Answer

How hard is it to change the clutch

on the ground it is a real pain, about 6-8 hours, suggest u buy a factory service manual, u will need a good full set of all types of hand tolls, a hydraulic floor jack (min 2 1/2 ton). safety jack stands and a helper is absolutely needed to get the transmission back in.

May 29, 2010 | 1997 Saturn SL

1 Answer

What Jack and stand to get for my '04 Ram 1500 Short Bed V6?


Mar 14, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides