Question about 2003 Chevrolet Malibu

Open Question

How reset anti theft mode equinox chevy 2006

Star with remote starter but then die and dont star with key

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: 2006 Chevy Equinox - Service Lamp Reset

Turn the ignition to run. Within three seconds push the gas pedal to the floor three times. Turn the key to off, and then start the car. The light should flash three times signifying that it reset. If it does not, try repeating the process, but instead of turning it to off after stepping on the pedal, just start the car.

Posted on Dec 22, 2008

handybc70
  • 25 Answers

SOURCE: 2006 Chevy Equinox

Hiya...the factory-installed keyless remote control are installed in most Equinoxes IF SO equipped with this option that year.
However, it's difficult to get "true factory-installed" keyless feature in your Equinox ....but new 2008-2009 Equinoxes built this year now comes with standard keyless remote and yes, new option is remote STARTER feature (that option is identified by a black wire found inside the rear-right quarter window with thin metal line surrounding that interior window to receive signal from remote starter fob)

At least you can find after-market keyless remote control at your local retail store.

Posted on Jan 31, 2009

emissionwiz
  • 75197 Answers

SOURCE: 2006 chevy equinox keyless remote programming

from the service manual:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Please go to the nearest GM dealer for assistance

Posted on Mar 26, 2009

  • 31 Answers

SOURCE: 97 Chevy Monte Carlo won't start, security light is on

disconnect battery for 24 hrs so the computer will reset and if that dont work take it to chevy dealer and have them reset it manually

Posted on Mar 27, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 1500 Chevy Silverado - microchip for anti-theft?

Document ID# 803013
1999 Chevrolet Chevy K Silverado - 4WD

Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960)
1999-2001 Chevrolet and GMC C/K Pickup and Utility Models (Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL)

This bulletin is being revised to add information on inspecting for electrical intermittent conditions and important connector C201 tightening steps. Please discard Corporate Bulletin Number 01-08-56-002 (Section 08 -- Body and Accessories).

Condition
Some customers may comment on the following conditions. These symptoms may be intermittent.

• Security lamp illuminates while driving. The Security lamp may be On or Off when the customer brings the vehicle to the service facility.

• The engine cranks but will not start and the Security lamp is flashing.

• The engine starts then stalls and the Security lamp is flashing.

Cause
Condition(s) may be due to an incorrect Passlock™ sensor voltage received by the body control module (BCM) from the Passlock™ sensor due to the following conditions. Most intermittent conditions are caused by faulty electrical connections or wiring.

• A 7 ohm variation in the sensor ground circuit wiring, circuit 1057

• A 100 ohm variation in the Passlock™ sensor signal wiring circuit, circuit 1836

Inspect for the following items:

• Broken wiring inside the insulation.

• A poor connection between the male and female terminal at the connector. Refer to Testing for Proper Terminal Contact under Testing for Intermittent and Poor Connections in Wiring Systems for the specific procedure.

• A poor terminal to wire connection. Some conditions that fall under this description include poor crimps, poor solder joints, crimping over the wire insulation instead of the wire itself, and corrosion in the wire to terminal contact area.

• Wire insulation that is rubbed through. This causes an intermittent short as the bare area touches other wiring or parts of the vehicle.

• A poor connection between the male and female terminal at a connector. This poor connection may be the result of contamination or deformation.

- Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the connector itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or underbody connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

• Separate the connector halves.

• Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that shows signs of contamination should be replaced in its entirety including the terminals, the seals, and the connector body.

- Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or repeatedly separating and joining the connector halves. Deformation, usually to the female terminal connector tang, can result in poor terminal contact causing an open or intermittently open circuit. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between an good terminal and a suspect terminal. Replace the female terminal in question.

Correction
Have any of the following components had service recently?

• The BCM

• The ignition lock cylinder case assembly

• The PCM/VCM

If any of the above components have been replaced, the Programming Theft Deterrent System Components procedure must be performed before any diagnostic procedures are performed.

To assist in diagnosis, the following steps are provided.

Does the engine start? If not, use the Engine Cranks but Does Not Run diagnostic information in the Engine Controls sub-section of the applicable Service Manual.
Important:

• The Security telltale on the message center is controlled by the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The Security telltale is controlled by the BCM through the Class 2 data line.

• The VTD system portion of the BCM controls the Security telltale when the ignition switch is in the On position. The VTD system uses the Security telltale as a malfunction indicator.

• The CTD system portion of the BCM controls the Security telltale when the ignition switch is in the Off position. The CTD system uses the Security telltale to identify system status.


Observe the Security indicator lamp in the instrument panel.
Remove the key from the lock cylinder.
- Security indicator should be Flashing when the door is open.

- Security indicator should be Off when all the doors are closed.

- If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual.

With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp.
- Lamp is On and does not go Off however, the engine starts. This indicates that the VTD system detected a fault when the engine was running.

- Lamp flashes On and Off. This indicates a problem has been detected by the VTD (Passlock™) system and the engine may not start this key cycle, a current condition.

Important: You must diagnose the diagnostic trouble codes (DTCs) in the order specified in the DTC table shown below. Failure to do so may result in one or more of the following conditions:


• Extended diagnostic time

• Incorrect diagnosis

• Incorrect parts replacement


DTC
Diagnostic Procedure
Module

Important: Before you use this table, diagnose P0601, P0602, P0604, and P0606. Refer to Diagnostic System Check - Theft Deterrent.

PXXXX Other PCM DTCs

Refer to the following procedures:

• Diagnostic System Check - Engine Controls in Engine Controls - 4.3L

• Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, 6.0

• DTC P0192 in Engine Controls - 6.6L

• Diagnostic System Check - Engine Controls in Engine Controls - 8.1L


If none of the above items are true, proceed with the following steps:

Install seat covers.
Connect the scan tool to the diagnostic link connector (DLC).
Enter scan tool diagnostics.
Select the model year of the vehicle.
Select light truck.
Select F1, (Body).
Select "C" or "K" for Series.
Select F0, Body Control Module.
Select F0, (Diagnostic Trouble Codes (DTC)).
Select F0, (DTC information).
Select F0, (Current DTC).
Record on the repair order any current DTCs displayed. If none, skip the next step.
Is a current B2960 DTC displayed? If no, the condition is not present with this key cycle. Continue to the next step.
Select Exit.
Select F1, (History DTC).
Are any history DTCs other than B2960 present? If so, diagnose those DTCs first using the appropriate service information, otherwise continue.
Select Exit.
Select Exit.
Select F1, Data Display.
Select F6, Security.
Cycle the key to the OFF position and wait 20 seconds.
Slowly turn the key to the RUN position. Be careful not to turn the key into the START position.
Observe the following values:
- Passlock™ Data Voltage should be 5.0 volts.

- Passlock™ State should be Normal.

- Passlock™ Code should be Open.

Rotate the key to the START position, and observe the following again:
- Passlock™ Data Voltage should be less than 5.0 volts. Passlock™ Data Voltage should remain steady and not fluctuate. The test vehicle used for this diagnostic procedure had a voltage value of 2.49 volts. The vehicle being worked on may be either higher or lower than this value. The key is that it has to be less than 5.0 volts.

- Passlock™ State should be "Monitor Passlock™".

- Passlock™ Code should be Valid Code.

If no trouble is found and the customer has experienced one of the symptoms or the code is a history DTC, the most likely cause is the VTD (Passlock™) wiring, specifically the wires from the VTD (Passlock™) sensor to the BCM.

Posted on May 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2008 equinox anti theft doesnt work and starter will not engage


Anti theft is working and that's why starter isn't engaging. This may work. Turn key on and leave on for 10 minutes. Turn off for 10 minutes. Turn on and wait for security light to go off. Then try to start car. This process works on most GM vehicles that have forgotten the key.

Oct 29, 2016 | Cars & Trucks

2 Answers

2006 chevy express van reset anti theft system?


there may also be a "key chip" that goes under the dash, I have seen those fall out and keep the car from starting (looks kind of like a wide USB fob such as this:
25356510-sxneijxydcsro1nodh24pjva-5-0.jpg

Jan 05, 2015 | Cars & Trucks

1 Answer

2007 equinox beeping when unlocking


i think thru the drivers infromation center you can disable that option or add key fobs

Feb 22, 2013 | 2007 Chevrolet Chevrolet Equinox LT

2 Answers

Replace a key ignition out of my 2005 chevy equinox with a 2006 saturn vue now the chevy wont start cause of the theft system. how do i reset this


The 2005 equinox is equipped with GM passlock anti theft security. By replacing the ignition you have broken the communication for this system. Your vehicle will never start again until you fix that properly. There is a way to bypass that system so it will work. I've done dozens of these bypasses and they work great. Best part is you'll never have to worry about it again. Go to this link and read up on how this system works. The bypass YOU need is under "permanent fix". Trust me, this is your best bet. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Jun 08, 2011 | Chevrolet Equinox Cars & Trucks

3 Answers

How do you reset anti theft on a 2007 equinox


TURN ON IGNITION SWITCH TO ON POSITION.ENGINE OFF.REPEATEDLY PRESS VECHICLE INFORMATION BUTTON UNTIL PRESS TO RELEARN REMOTE KEY IS DISPLAYED.PRESS SET RESET BUTTON UNTIL REMOTE KEY LEARNING ACTIVE IS DISPLAYED. IF THAT PROCEDURE DONT WORK.INSERT MASTER KEY INTO IGNITION SWITCH.NOW SWITCH IGNITION ON SWITCH IGNITION OFF.REMOVE MASTER KEY.WITHIN 10 SECONDS INSERT NEW KEY.SWITCH IGNITION ON.ENSURE SYSTEM WARNING LAMP SWITCHES OFF.NEW KEY NOW PROGRAMMED.IF YOU STILL HAVING PROBLEM RESETING THEFT SECURITY SYSTEM THE DEALERSHIP HAS TO FIX.REPROGRAM IT.

Mar 14, 2011 | 2007 Chevrolet Equinox LS New Cars

2 Answers

No start cranks but does not fire has spark. has fuel if bypassed by relay fuses good new fuel pump a year ago has fuel replaced battery froze, has prostart remote start, been in 8 years no issues 2000...


check to see if the security light or anti theft light flashes. if that is the case, sounds like the bypass for the remote starter may be causeing the no start by tripping the anti theft system. Remove remote starter and bypass system and join any cut wires back together that may be cut for remote starter. Try starting, if theft light still flashes leave key in the on position after attempted start for 15 minutes till theft light goes solid, turn off and try again. Repeat process for three times to re-learn factory theft system in vehicle. If problem still persists, then take to your local dealer to reprogram factory theft module in the cluster.

May 31, 2010 | 2000 Chevrolet Cavalier

2 Answers

99 chevy cavalier theft system light on steady, car wont crank.


My 2000 cavalier has done this for 6 months. You take your key out then open your door, wait ten minutes and the system resets itself and the car will start-annoying you bet!!!

Jul 20, 2009 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

97 Chevy Monte Carlo won't start, security light is on


disconnect battery for 24 hrs so the computer will reset and if that dont work take it to chevy dealer and have them reset it manually

Mar 27, 2009 | 1997 Chevrolet Monte Carlo

1 Answer

2006 Chevy Equinox


Hiya...the factory-installed keyless remote control are installed in most Equinoxes IF SO equipped with this option that year.
However, it's difficult to get "true factory-installed" keyless feature in your Equinox ....but new 2008-2009 Equinoxes built this year now comes with standard keyless remote and yes, new option is remote STARTER feature (that option is identified by a black wire found inside the rear-right quarter window with thin metal line surrounding that interior window to receive signal from remote starter fob)

At least you can find after-market keyless remote control at your local retail store.

Sep 23, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2003 Chevrolet Malibu Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...