Question about 1990 Jeep Wrangler

Open Question

How to bleed clutch master cylinder on 1988 jeep comanche

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
redbeard00
  • 957 Answers

SOURCE: how do i bleed the master clutch cylinder system on a 1995 jeep ?

A special pump is used to back bleed the system. If you don't own one then you have to be patient and just keep pumping the clutch pedal until it comes back. It can take a half hour to get it back. Just depents on how much air is inside.

Posted on Jun 16, 2009

Ad
  • 1810 Answers

SOURCE: 1988 Jeep Comanche transmission will not shift automatically

chapters and indago sell chilton books they are a god send the have all the wiring diagrams in the back of the book also auto zone carries the books too

Posted on Jan 13, 2010

  • 67 Answers

SOURCE: WHERE IS THE CRANK CENSOR LOCATED ON A JEEP

on transmission near bellhousing

Posted on Mar 30, 2010

  • 96 Answers

SOURCE: where is the slave cylinder on a 1988 Jeep

I'm assuming you're referring to the clutch slave cylinder... It is located on the input shaft to the transmission. You'll need to separate the ****** from the engine in order to access it.

Posted on Aug 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I bleed the air out of my clutch system I replaced the clutch master cylinder and it or the slave cylinder doesn't have a bleed screw it's an 1987 jeep comanche


amazing 4 manual boxes then,. ill pick one
like my Comanche.

which engine? mine was the 4L , all show photos for that... only.
i had the 88, and have books on it.
it's old
that 5speed, is French Peugeot. trans. (my 99 was Mitsubishi box)
with a Peugeot, coaxal, (hidden) throwout/bearing and integrated
slave.
my 4wd, took me 10 long hours on stands to pull the trans.
in and out.
yes, that sux.
iv posted this and photos before.
searches can work.

the coax clutch has and extension tube , that passes through the bell grommet and has bleeder tip on that, yes , alien stuff.


26189380-3t1zcnjngeatxnm4yyvjcbdi-2-0.jpg

26189380-3t1zcnjngeatxnm4yyvjcbdi-2-1.jpgphotos work , no?
all this is online
mitchels.
and alldata.com.
and very rare, this data is,,,,, this old.26189380-3t1zcnjngeatxnm4yyvjcbdi-2-3.jpg

May 09, 2016 | 1987 Jeep Comanche

1 Answer

How to bleed master clutch cylinder on a 1988 chevy s10


Bleed master first and then slave get tube on bleed nipple and keep pumping into bottle keeping tube in fluid in bottle so it will not draw air on return stroke some cars can be quite hard too bleed

Nov 18, 2015 | Cars & Trucks

1 Answer

No leaks in breaks still no pressure


Replace master cylinder kit and bleed the master cylinder. Check for pressure at the wheels. If there is the bleed the whole system. If no pressure check for blocked pipes. The hoses are normally the problem but they would not go at the same time.

Sep 14, 2012 | 1988 Jeep Comanche

1 Answer

Where is the slave cylinder on a 1988 Jeep comanche


I'm assuming you're referring to the clutch slave cylinder... It is located on the input shaft to the transmission. You'll need to separate the ****** from the engine in order to access it.

Aug 24, 2011 | 1988 Jeep Comanche

1 Answer

I have a 1988 jeep wrangler when i let it sit for a little bit i have a little bit of clutch pedal but after i bleed it. theres nothing at all. Then i let it sit and it will get a little better but then i...


it sounds like a faulty clutch slave cylinder. If you cannot keep pressure, then this is where to start. bench bleed the clutch master first if possible then when installed in the car be sure to get ALL the air out then continu on from there. If no pedal still thn perhaps you have a faulty clutch and it will not allow the clutch to disengage. good luck!

Aug 24, 2010 | 1988 Jeep Comanche

1 Answer

How do I repair or rebuild a leaky hydraulic clutch in a '88 jeep comanche


Best if you replace the leaky master unless you have complete access to proper tools including hone to rebuild what you have.

Jun 20, 2010 | 1988 Jeep Comanche

1 Answer

I have to put hydraulic fluid in it just to change gearsbwhile pumping the clutch


the master or slave cylinder has a bad leak,i always change both as its easier.you only have to bleed once.....

Jun 19, 2010 | 1987 Jeep Comanche

1 Answer

Clutch is bleeding down


Check for leaks at the master cylinder, if none found then most of the slave cylinders are internal and you have to pull the transmisson out to get to them.

Mar 03, 2010 | 1988 Jeep Comanche

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler


1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Jan 14, 2010 | 1991 Jeep Wrangler

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
1990 Jeep Wrangler Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...