Question about 2007 Chevrolet Impala LS Sedan New Cars

Open Question

Remove rear Bumper cover on 2007 Impala - 2007 Chevrolet Impala LS Sedan New Cars

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Ben-mrfixit
  • 68 Answers

SOURCE: front bumper cover support

sounds like you need a new front end clip

Posted on May 03, 2009

Ad
smartr10U
  • 1305 Answers

SOURCE: remove rear seat impala2007

To remove the rear seat, pull up on the front of the seat bottom, it should be hooked in place by spring type clips. After you get the front edge up, pull out the seat. This should expose the bolts/screws that hold the seat back in. Look below and there should be a couple of screws holding the seatback to the car body. Remove these and then you can pull the seat back out of the car.
K

Posted on Aug 29, 2009

  • 1 Answer

SOURCE: How do I remove the rear bumper on a 2003 malibu?

I WANT TO REMOVE AND REPLACE REAR BUMPER

Posted on Jan 29, 2010

  • 4 Answers

SOURCE: how to remove the front bumper cover on 2002

Remove all eight small set screws (4) on each side in the fender wheel wells. Then remove the four secure bolts on undercarriage of bumper (4). Take a screw driver. (flathead) to the upper portions of both the left and right side of the bumper. Be careful....... These are extremely fragile and you may need to replace them before replacing the bumper. Then comes a bit unnerving part. Removal of the bumper........ (This scarred the **** out of me!!!!) just grab ahold of one of the corners, then gradually pull! That's it. The clips will come out gradually and evenly.

Posted on Feb 20, 2011

  • 21 Answers

SOURCE: How to remove a 2007 Avalanche rear bumper

Get 20-30 feet of heavy chain. Attatch bumper to large tree. Floor the gas. :(

Posted on Aug 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing rear bumper cover for 2007 uplander


Lift the tail gate. There are clips or screws along the top edge. Remove this. The clips all you do is pull the center pin with a panel tool or pliers then the rest will come out. Then you will need to remove the clips holding the rear side of each of the back wheel wells in. Under that will be more clips, screws or bolts that hold the side edges of the bumper cover on.

Aug 19, 2016 | 2007 Chevrolet Uplander

1 Answer

How to remove rear bumper cover on a 2003 chevy impala?


The top and bottom are held in place by plastic plugs. Where the bumper meets the metal, There are two bolts on each side.

Jun 29, 2016 | 2003 Chevrolet Impala

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

How to replace right front fender on a2007 replace fender 2007 chevy impala


There are four bolts and the hood hinge to remove on top. Remove the tire, remove the inner fender cover( seven or eight screws). There are two bolts to remove the fender from the front bumper cover. And one bolt to remove from inside the door( open the door, remove the cloth, the bolt is close to the top). Replace in reverse.

Oct 09, 2014 | 2007 Chevrolet Impala

1 Answer

Removing rear bumper cover on 2007 Chevrolet Impala?


Most dents can be popped or tapped back out, provided it has not crumpled or creased the metal.


---------------------------obd2express.co.uk

Dec 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

How do you replace a bumper bar ....do you need a whole new skirt


Bumper bar? Skirt?
There is a bumper reinforment behind the bumper cover.
Front or rear???
Either way there are some plastic retainers on top. You may need to remove a grill which would have some sort of retainer. The retainers usually have a center section that prys up some and the retainer will then pull out.
There should also be some retainers on the undersides of the bumper covers.
There is just about always a bolt going up through the bumper cover into the rear quater panel or front fender right in the wheel well edge. Sometimes there is a guide that the cover slide onto as well. You may need to remove the tail lights. There will be nuts on the inside behind the trim panels or the headlights. they usually have some clearly seen bolts holding them in (about 4 give or take)
Unplug any lights and they can usually be left in the bumper cover.
Then off comes the cover.
From there you may find a styrofoam pad. Don't lose that as it helps the cover keep its shape in the heat. And either the reinforment will be bolted or welded to the frame rails.

Sep 06, 2011 | 2007 Toyota Camry

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

I want to fit a towbar to my ford focus hatch 2008 model. What is involved in removing rear bumper Regards Brian Lamb


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Oct 27, 2009 | 2007 Ford Focus (3 Door) Hatchback

2 Answers

2007 buick lucerne has water leaking into the spare tire wheel well. please advise


Remove trunk trim and covers , close trunk and wet car now look for leak source.

Jun 16, 2009 | 2007 Buick Lucerne CXS Sedan

Not finding what you are looking for?
2007 Chevrolet Impala LS Sedan New Cars Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...