Question about 2000 Dodge Dakota Quad Cab

1 Answer

Could a map sensor cause a service code p1391

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 645 Answers

This is the code table: chinasinoy.com

Posted on Dec 06, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 100 Answers

SOURCE: i have an 02 dodge ram 1500 4x4 it started

You probably have a bad ignition coil. Which engine is in this truck? 3.7, 4.7, 5.7 or hemi

Posted on Jan 07, 2011

dttech
  • 4803 Answers

SOURCE: Code P1391, replaced camshaft and crankshaft

DIAGNOSTIC TROUBLE CODE (DTC) P1391: "INTERMITTENT LOSS OF CMP OR CKP"
This DTC is monitored with the engine cranking or running. This DTC will be stored in the Powertrain Control Module (PCM) when the PCM FAILURE COUNTER reaches 96 failures for 2 consecutive trips.
Posiible causes are: Craknkshaft Position (CKP) sensor improperly installed, defective CKP sensor, defective distributor, defective Camshaft Position (CMP) sensor, defective PCM, defective or broken flywheel, defective connectors or defective wiring.
Proper diagnosis is recommended before replacing ANY parts.

Posted on Oct 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 dodge avenger p1391 code, had no start first with no code and replaced dist..didnt fix it..then replace crank sensor and that worked..ben running fine for a year..now all of sudden runs crappy and...


Check connections to crank sensor, then reset your comp by disconnecting your battery cables and holding them together. Make sure to have the code cleared as well.

P1391 (M) Intermittent Loss of CMP or CKP Loss of the Cam Position Sensor or Crank Position sensor has occurred.

Apr 14, 2013 | 1998 Dodge Avenger

1 Answer

What do code p1391 mean


P1391 means intermittent loss of CKP and CMP , these sensor are monitor when the engine cranking,or running,These can come from a damage flex plate for the cranksensor or damage tone wheel for the camsensor,to a failing cranksensor ,failing camshaft sensor, to even the harness intermittent connnection

Mar 12, 2012 | Cars & Trucks

1 Answer

Code P1391, replaced camshaft and crankshaft sensors, plugs and wires, rotor, and a couple fuses, can a loose or bad distributor be the cause for this code?


DIAGNOSTIC TROUBLE CODE (DTC) P1391: "INTERMITTENT LOSS OF CMP OR CKP"
This DTC is monitored with the engine cranking or running. This DTC will be stored in the Powertrain Control Module (PCM) when the PCM FAILURE COUNTER reaches 96 failures for 2 consecutive trips.
Posiible causes are: Craknkshaft Position (CKP) sensor improperly installed, defective CKP sensor, defective distributor, defective Camshaft Position (CMP) sensor, defective PCM, defective or broken flywheel, defective connectors or defective wiring.
Proper diagnosis is recommended before replacing ANY parts.

Oct 21, 2011 | 1999 Dodge Dakota

1 Answer

Getting a P1391 error code on my 01 Caravan, Changed PCM Sensors, wires, plugs, EGR, Whats Next? Please


P1391 Glow Plug Circuit Low Input (Bank #1)
  • DTC P1391 or P1393 will set when the monitor indicates that all four glow plugs are not being powered on that bank. An open in the glow plug circuits, glow plug relay, glow plugs or monitoring circuit could be the possible causes.

    Both DTCs P1391 and P1393 together will set when the monitor indicates that all eight glow plugs are not being powered. An open in all glow plug circuits, the glow plug relay, glow plugs, fusible links or all three monitoring circuits could be the possible causes.
  • Possible causes:
    • glow plug relay
    • glow plug shunt
    • open in glow plug circuit(s) or monitoring circuit(s)
    • glow plugs
    • PCM
__________________

May 19, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

What are these codes that appears on my engine check machines? p1391,p1297,p0108,p1492


P1391 Intermitant loss of cam or crank; P1297 No change in map from start to run; P0108 Map sensor voltage too high; p1492 Battery temp sensor too high.

Apr 16, 2011 | 2002 Chrysler Sebring

1 Answer

What could be wrong with a 1997 Isuzu rodeo with g sensor codes p1391 p1393


The G Sensor monitors any abnormal vertical motion of the vehicle (such as a rough road condition like going over bumps or hitting potholes) and helps the power control module (PCM) determine if the changes in the crankshaft speed are due to engine misfire or are driveline induced.

You can look for a poor connection at the PCM...or a damaged harness. The G Sensor shares PCM 5V and ground terminals with the MAP sensor...a damaged MAP sensor or harness could cause the alarm. And finally, the G Sensor will give correct voltages to the PCM only if it is level and mounted securely to its bracket.

Mar 25, 2011 | 1996 Isuzu Rodeo

1 Answer

Code p1391


P1391: Loss of the camshaft position sensor or crankshaft position
sensor has occurred. This can cause the car to start hard or not start at all. Replace both of these sensor should fix the problem.

Nov 13, 2010 | 2000 Dodge Intrepid

1 Answer

What does the p1391 code on a 99 dodge ram 1500 5.2l v8 meen


check engine light and code P1391 crank or cam position sensor

The above can cause rough idle on the Dodge Ram 1500 5.2L V8 Engine.

Can try to replace the sensor, but verify that the wires are ok first.

Aug 12, 2010 | Dodge Pickup Cars & Trucks

1 Answer

JEEP CODES P1391 AND P1398


p1391= crankshaft / camshaft position sensor intermitant signal, check, wiring, connections & sensors
p1398= engine control system missfire detection limit reached probable causes, wiring,poor connections,engine mechanical fault,ignition/fuel system fault (causing misfire) or camshaft/ crank shaft position sensor

Jun 04, 2010 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Dodge Dakota Quad Cab Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...