Question about Cars & Trucks

Open Question

1998 Chevy 1500 rear axle and differential

Need diagram for 1500 chevrolet rear axle and differential

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: rear differential axle removal

remove the 'locking bolt', once the pin is out the c-clips shoud fall out unless this is a floating axle in which the axles are attached at the hub.

Posted on Sep 12, 2008

Ad
  • 10 Answers

SOURCE: can not remove rear axle on chevy avalanche 4x4 1500.

you will need to take off the differential cover (drain and change diff oil at this time)

rotate the axle so that you can get at the cross pin and remove it by undoing a small bolt that holds it in place. it should slide out with ease, but i have had them stick, take care not to let the cross pin get lodged where it is difficult to extract

a single C-clip is holding each axle inside the differential housing

you will need to push in from the outer end of the axle, while simultaneously manipulating the C-clip off of the inner axle, repeat this same process on the other side

i will put some of pics up in a minute

Posted on Feb 09, 2009

  • 1 Answer

SOURCE: remove front axle from differential on 2003 dodge ram

That works fine on a relatively new vehicle but one that has run in salt etc you'll save a lot of time if you remove the steering knuckle completey by separating lower ball joint and outer tie rod end ball joint and bring the whole steering knuckle to a bench to separate the hub/bearing. Soak everything with penetrant, loosen the bolts a few turns and try hitting right on the bolt heads. I also made a very sharp wedge from a chisel and rammed it hard on the other side to seoarate the hub. It will finally come apart then you'll see all the **** that was binding it due to an alumininum knuckle re-acting with a steel hub. Clean the hole and grease everything and fit new bearings

Posted on Feb 15, 2009

Molson02536
  • 3854 Answers

SOURCE: 2003 chevy suburban front axle noise

Worn side bearings is where the noise is coming from and might as well do both sides, I used replace them in about 2-4 hours, depending on where Murphy happened to be. Disconnect both side inner CV joint, front prop shaft and the 4X4 actuator line. If you want to drop the front pumpken. Not sure if you have enough room if you want to change the bearing without removing the pumpken from the frame. You should see when you disconnect the CV shaft.

The front diffs are toys compared to the rear, if you use auto4wd too much there are bearings in your tranfer case that are similar to the side bearings in the front diff. In both appearance and durability and soon you'll replace those too.

Good luck and keep me posted.

Posted on May 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear end axle removal for a 2000 chevy truck 1500


You must remove the rear cover on the differential and then the spider gears, then the center pin bolt and the pin then push in on the axle and remove C clip retainer inside the gear carrier and slide axle out.

Mar 27, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

Is there any other way to remove the rear differential from my 1998 Chevy Tahoe if I don't have and can't rent a rear spreader ?


never needed a spreader on a tahoe with the axles out put a heavy rag between the gears and rotate the pinion you need to remove it evenly

Jun 27, 2012 | 1997 Chevrolet Tahoe

2 Answers

How to rear axle on chevy express van 1500


You want to know how to remove the axle correct ? There are clips inside the rear carrier that hole the axles from running out . You need to remove the the bolts on the back of the rear carrier but make sure that you can get the fill plug out first so you can put oil back in it . The clips come out like nothing you can do it with your fingers you need to replace the seals and look at the axle shaft and condution of the bearings replace as required also check to see if the vent is clear on the carrier the oil is heavy and expands alot this will blow the axle seals . The older it is the more likely it is that you need axle s or bearings but you will need new seals if you remove the axles

May 21, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Have a Leaky seal on left side of differential. Need to repair or replace. Need a Chevy Astro 1998 front differential diagram


front or rear wheel drive ,as only ones i havew worked on are rear wheel drive ,so do you mean the half shaft seal

Aug 15, 2010 | 1998 Chevrolet Astro

1 Answer

Were do you refill rear end differential on 98 Dodge Ram 1500 4x4


On the rear differential there will either be a metal plug or a rubber plug. The metal plug can be removed with a 3/8-inch drive ratchet. the rubber plug can be removed with a small screwdriver. Faceing the axle from the rear will see the plug to the right side on the cover plate. Remember to also check the front differential as well. Hope this will help you.

May 13, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

How do you service the front trans axle on 2002 silverado


There is a drain plug and a upper fill plug on the front differential, and believe it's in the passenger side. but i could be wrong on the side. The age thing but you can see both of the plug than you need to drain and re-fill.

2002 CHEVROLET TRUCKS SILVERADO 1500 PICKUP 5.3L 8-cyl Engine Code [T]

Differential, Front / Rear Full time 4WD......GLS ALL TEMPS....Synthetic Extreme Pressure (EP) Lubricant 75W-90 (SVG)

GM part no. 12378557 or equivalent Do not add friction modifier.

CAPACITIES:
Differential, Front..........1.7 liters
Rear differentials
Differential, With 10.5 RingGear Amer Rear..........2.6 liters
Differential, With 11 RingGear Dana Rear..........4 liters
Differential, With 11.5 RingGear Rear..........3.6 liters
Differential, With 8.6 RingGear Amer Rear..........2.3 liters
Differential, With 9.5 RingGear Amer Rear..........2.6 liters
Differential, With 9.75 RingGear Rear..........2.8 liters

Good luck and this should help.


Dec 26, 2009 | 2002 Chevrolet Silverado

1 Answer

2001 Chevrolet Silverado How to remove rear axle on 2001 chevrolet silverado


Remove...
wheels, drums or rotors, the cover for the differential (You will need a drip pan)
remove the "pin" (usually a 5/15" or 8mm head) that secures the spider gear pin. Remove the long spider gear pin, as it should slide out without a lot of force.
Push both axles inward, and remove the left and right "c" clips that hold the axles in.
Note... if you have a limited slip, it may be a little different of a set up due to clutches in the differential.

Nov 05, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

How do you remove the differintial on a 2004 chevy pick up 1500?


Get the rear wheels off of the ground, remove wheels, and drums. (Rotors if you have those)
Remove rear cover (use a drain pan to catch fluid)
Look for the 5/16" or 8mm head pin bolt and remove it.
Turn the differential so you can get the pin out. (goes through the center)
Push you axles inward and with a small magnet, take both "C" clips out from the inner part of the axles.
Now slide out you axles. (Careful on the outer seals)
Mark your carrier bearing caps so you know what is left or right, and remove them both.
Find out what size the bolt heads are for the "ring" gear and get two wrenches to fit. (Usually 19mm or 3/4")
Hold one on a bolt head on the top side and put the other wrench lower.Force the lower wrench upward, as this will push the upper wrench into the housing and "push" the differential out. When removing be aware that there are spacers that need to go back where they came from. DO NOT MIX THESE UP. These spacers are under the carrier bearing caps, left and right of the differential.
Note, four spider gears is a normal differential, requires gear oil. If it has clutch packs, it is a limited slip and requires gear oil and limited slip additive!!!

Sep 22, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

Can not remove rear axle on chevy avalanche 4x4 1500.


you will need to take off the differential cover (drain and change diff oil at this time)

rotate the axle so that you can get at the cross pin and remove it by undoing a small bolt that holds it in place. it should slide out with ease, but i have had them stick, take care not to let the cross pin get lodged where it is difficult to extract

a single C-clip is holding each axle inside the differential housing

you will need to push in from the outer end of the axle, while simultaneously manipulating the C-clip off of the inner axle, repeat this same process on the other side

i will put some of pics up in a minute

Feb 08, 2009 | 2002 Chevrolet Avalanche

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...