Question about 2001 Chevrolet Blazer

1 Answer

How to bleed a hydralic clutch on a 2001 chevy blazer

I need to no how to bleed the slave cylinder and the clutch?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 76,649 Answers

You must reverse bleed it. Go here to learn how. You will need to buy the tool pictured.

Posted on Dec 05, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

motor1258
  • 6674 Answers

SOURCE: 1994 chevy camaro 3.4manual 5 speed

You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Posted on Jan 31, 2009

  • 6982 Answers

SOURCE: leaking clutch 85 s10 blazer

First, unless you have just done some clutch work you should not need to be bleeding the clutch hydraulic system...that shows that it's leaking. There is nothing inside the bellhousing that has anything to do with clutch fluid, so, the fluid you see is either engine or transmission oil (rear main seal or seal on trans input shaft) Could it be that the clutch slave is leaking and it's running down and dripping at the bottom of the housing? (clean it up and check that)

Posted on Jun 17, 2009

  • 14036 Answers

SOURCE: HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500

raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Posted on Jul 19, 2009

  • 33 Answers

SOURCE: clutch pedal stays 2 the floor on a hydralic

Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Posted on Sep 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 Chevy S10 Blazer


If you need to bleed the clutch, you should notice a soft clutch pedal getting firmer when you pump it (the air that you need to bleed out of the system compresses as you pump, and the pedal gets firmer, just like brakes).

A hydraulic system for a clutch (or your brakes) has a master cylinder component and a slave cylinder component. If you compress fluid in the master cylinder, it exerts force on a (more than one for your brakes) slave cylinder that causes a mechanical component to move.

Recommend you lean into the engine compartment on the drive side at the firewall or crawl under the car and have someone depress and release your clutch a few times. You should be able to find the master cylinder because the mechanical clutch linkage has to be attached to it. The same at the bellhousing, where the slave cylinder has to mechanically cause the throwout bearing to be moved. It is possible (but not probable) that your clutch master cylinder is located on the inside of the firewall, not the outside.

Nov 07, 2013 | Cars & Trucks

1 Answer

How do you bleed the clutch and slave cylinder on a 2001 chevy blazer?


Usually there is a bleeder screw on the master or the slave, and you bleed it just like you would brakes.
But you should not be loosing fluid if the system is sealed.

Dec 05, 2012 | Cars & Trucks

1 Answer

1994 ford escourt clutch will not disengage fully, tried bleeding the hydralic clutch but still not disengaging fully. Any sugestions


could be slave cylinder or clutch master cylinder. might also be the throw out bearing binding up on the shaft not allowing full movement.

May 31, 2012 | 1994 Ford Escort

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

2 Answers

2008 corvette 11,200 miles on it clutch won't release


YOUR WARRANTY SHOULD FIX IT. SHOULDNT HAVE TO FIX YOUR SELF.POSSIBLE CAUSE CLUTCH MASTER CYLINDER FLUID LEVEL.IF LOW CHECK MASTER CYLINDER SLAVE CYLINDER LINES FOR LEAKS FIX AND BLEED CLUTCH HYDRALIC SYSTEM.IF CLUTCH MASTER CYLINDER FLUID LEVEL OKAY.THE CLUTCH DRIVEN DISC PRESSURE PLATE NEED ADJUSTMENT.I WOULD LET YOUR FACTORY WARRANTY FIX IT.YOU SHOULDNT HAVE TO PAY ANYTHING.JUST MAKE SURE FLUID IN CLUTCH MASTER CYLINDER NOT LOW WHEN YOU TAKE IT TO DEALERSHIP.IF THEY CHECK IT OUT FIND ANY KIND NEGLECT TO VECHICLE.THEY WILL NOT PAY.THEY WILL FIX BUT YOU WILL PAY OUT OF POCKET EXPENSE.

Oct 14, 2010 | 2008 Chevrolet Corvette

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

1 Answer

HYDRALIC CLUTCH BLEEDING 1993 CHEVY TRK 2500 ,AFTER REPLACING THE LINE


raise and support vechicle safely.remove slave cylinder.hold slave cylinder at a 45 degree angle.with bleeder screw at it highest point.have a helper fully depress hold clutch pedal.then open the bleeder screw. then close the bleeder screw.and have helper release the clutch pedal repeat the procedure until all of the air is evacuated from the system.keep check on on master cylinder keep fluid level full.to keep air from being drawn through the master cylinder.never release a depress clutch pedal with bleeder screw open.or air will enter the system.

Jul 19, 2009 | 1993 Chevrolet C2500

1 Answer

Need to bleed the hydralic clutch system on a 1993 chevy 2500 trk .Replaced old line,now need to bleed the rest of the air out


Should be a bleeder on the slave cylinder. remove the cover on the master and open the slave and let drip until fluid drops sdteady and no sign of air. Close slave and close master after replenishing the fluid. The first time you press on the pedal go slow and release real slow. Then you are off and clutching. Good Luck

Jul 19, 2009 | 1993 Chevrolet C2500

2 Answers

95 mazda b4000 slave cylinder bleeder valve location


the nipple sticks out side the bell housing on the left side just above your hydralic line for your clutch,auto zones web has a complete diagraham and steps for bleeding

Jun 17, 2008 | 1996 Mazda Pickup

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...