Question about Cars & Trucks

1 Answer

Windshield washer pump will not shut off 1983 chevy 1/2 truck

Pump continues to pump fluid when useing wipers replaced switch , did not fix problem

Posted by on

  • 3 more comments 
  • Mike johnson
    Mike johnson Dec 05, 2012

    I was thinking maybe a faulty pump, truck has set for years

  • Mike johnson
    Mike johnson Dec 05, 2012

    To my understanding the relay is built into the pump , does anyone know that to be the case.

  • Mike johnson
    Mike johnson Dec 07, 2012

    do u know if theres a relay for the washer pump and / or wiper motor , I think that the relay is built in the pump itself, but not sure if theres a relay at all

  • Mike johnson
    Mike johnson Dec 10, 2012

    I installed a universal washer pump , thanks for ideas. Mike J

  • Tony DelPlato Jul 21, 2013

    the 83 Chevrolet pickup has a control module between the switch and motor, this module is probably the culprit, check your local salvage yard first before ordering from aftermarket because the price is around $170, you can access the module from dash

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 95 Answers

You have a short

Posted on Dec 05, 2012

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: 2000 Jeep Cherokee Windshield Washer

You have a motor for the front and rear washer. Check the fuses. If the intermitted wipers does not work, there is a relay under the dash near the steering colum that needs to be replaced.

Posted on Jan 01, 2009

  • 1 Answer

SOURCE: Windshield washer Pump doesn't run, but the pump checks out good

there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there



Posted on Jan 21, 2009

01fordeb
  • 1033 Answers

SOURCE: 1998 ford expedition front windshield washer

fuse for washer pump, can you here the pump, if not then power to pump isn't present. Check the fuse for it.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

1999 chevy prizm windshield washer fuse location?


If your windshield wipers are working than the fuse is good. The wiper and the washer use the same fuse.

The washer pump will have power to it all the time with the key in the on position. you can disconnect the connector and check this. The washer pump is grounded by the wiper switch. you can check the other wire for continuity to ground with the washer button depressed.

If there is power and ground at the connector than the pump is bad.

Sep 16, 2015 | Cars & Trucks

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

Where can I purchase fuse #45 for my chevrolet equinox lt 2007 in richmond, va


It sounds as if the windshield washer pump, located at the base of the windshield washer fluid reservoir, has lost it's seal. When this occurs, washer fluid seeps into the pump and shorts it out. I advise that you remove the pump to confirm this before replacing the fuse. A replacement wind washer pump and fuse can be found at your dealer, local auto parts store or the internet (Rockauto.com has always been a great source for quality parts at a very competitive price and I use them all the time). Hope this helps.

Mar 15, 2014 | 2007 Chevrolet Chevrolet Equinox LT

2 Answers

Windshield washer not working


  1. check your windshield washer fluid level.
  2. make sure you can hear the fluid pump operating when you operate the switch.
  3. If you can hear the pump working and you have fluid in the reservoir but still no spray,
  4. check the washer fluid lines don't have holes and aren't clogged or pinched. check the sprayer nozzles make sure they are not clogged with debris.
  5. if your washer still doesn't work your fluid pump is probably the problem.

Sep 28, 2013 | 1999 GMC Jimmy

2 Answers

No windshield washer fluid pumping


1) Fluid resevoir is empty
2) Fluid is frozen
3) Washer fluid hose is disconnected, blocked or kinked
4) Washer switch is faulty
5) Washer pump motor is defective
6) Washer pump fuse is blown

Dec 24, 2010 | 2003 Oldsmobile Alero

3 Answers

I have a 2003 Chevy Trailblazer Windshield Wiper problem.


As it turns out, there is a recall On 2002-2003 Chevy Trail Blazer's
Windshield Wiper/washer
NHTSA No. 04V046000
Recall Date: Feb, 4th, 2004
Call your dealer to see if this is still under the recall to be fixed.
RECALL: 2002 - 2003 Chevrolet Trailblazer NHTSA Campaign Number: 04V046000 www.nhtsa.dot.gov
Manufacturer GENERAL MOTORS CORP. Recall Date: FEB 02, 2004 Potential Number Of Units Affected: 581394 Description VISIBILITY:WINDSHIELD WIPER/WASHER Summary CERTAIN SPORT UTILITY VEHICLES HAVE WINDSHIELD WIPER SYSTEMS THAT WILL NOT TURN ON, CEASE OPERATION WHILE IN USE, FAIL TO TURN OFF/ON BY THEMSELVES (MOISTURE SENSITIVE WIPER SYSTEM), OR HAVE CONTINUOUS WINDSHIELD WASHER PUMP OPERATION BECAUSE THE PRESENCE OF WATER WITHIN THE WIPER MODULES CAN EITHER CAUSE A SHORT CIRCUIT OR CAN LEAD TO THE CORROSION OF COMPONENTS WITHIN THE MODULE. Consequence DEPENDING ON THE OCCURRENCE AND WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, WHICH COULD RESULT IN A CRASH. Remedy DEALERS WILL COVER THE WINDSHIELD WIPER MODULE VENT HOLE WITH A PATCH. ALSO, THE WIPER MOTOR, CIRCUIT BOARD, AND ELECTRICAL CONNECTOR WILL BE INSPECTED TO SIGNS OF WATER INTRUSION AND/OR CORROSION AND BE REPLACED AS REQUIRED. THE RECALL BEGAN JULY 6, 2004. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR GMC AT 1-866-996-9463.

Nov 25, 2008 | 2003 Chevrolet TrailBlazer

1 Answer

Giovanni


I have a 1983 Royal Knight SS. Had the same problem. Had my wiper motor and washer pump replaced. works like a dream now. replaced my original combination turn signal wiper switch on steering column and now have good working intermittent wipers. It is great to see driving in the rain now. Jackson  in ATL

Oct 01, 2008 | 1983 Chevrolet El Camino

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...