Question about 2000 Nissan Quest

1 Answer

No electric supply to injector nozzles

The engine does not start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 180 Answers

Injectors fire like spark plugs, u need to have a diode tester lite,unplug an injector plug the diode into injector plug, then turn engine over and that will let u know if they are firing

Posted on Dec 05, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the fuel injector for a 2008 chrysler pt cruiser?


To remove a fuel injector or injectors you must remove the fuel supply rail that sits over them. Here is how you do that for both engine options, Turbo and non Turbo..

Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRB® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

How to replace the fuel injector on a 2008 chrysler pt cruiser


Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRB® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

3 Answers

Nissan Maxima engine oil smells like gas. White smoke coming from tail pipe


if the oil smells like gas then there is either too much fuel entering the cylinder and not being burnt or the oil has not been changed with in the change interval. also if you take short trips a lot this can cause this as the engine won`t get hot enough to burn excess fuel and it is always in cold mode allowing more fuel supplied than is needed. the white smoke usually indicates coolant burning, but keep in mind when its cold out you will get what looks like white smoke but is steam from the exhaust. does the smoke smell like something sweet as this will indicate coolant.

Apr 07, 2015 | Nissan Maxima Cars & Trucks

1 Answer

My ck2 lancer hard starts and the engine check light lights up about 1 minute after startup, what is causing these problems [4g13 engine]


its an injectors nozzles problem im sure of it
might be dirty nozzles needs to be cleaned and clogged up
or the nozzles are getting wider spraying hole so rather than spry the fuel it dripping it causing such a start up problems
but the sure thing is you need just check the injectors nozzles
have a nice day

May 30, 2011 | Mitsubishi Lancer Cars & Trucks

1 Answer

Where would i locate the fuel filter on a 1999 Ford taurus Se at?


Fuel Injection
General Information (System Description)
Electronic fuel injectors for all gasoline engine applications are basically
the same. They consist of an injector body, an electric solenoid, spring, nozzle
and a filter. The injector is supplied a constant supply of pressurized fuel
from the fuel system. The primary function of the fuel injector is to atomize
gasoline into the surrounding air at the proper time. Throttle body injectors
atomize fuel into the intake manifold in much the same manner as a conventional
carburetor (wet intake); port fuel injectors direct the atomized fuel at the
back side of each cylinders intake valve(s) (dry intake). Gasoline direct
injection systems operate at substantially higher pressure and direct the
atomized fuel directly into the combustion chamber of each cylinder.
---
Az Filters/Fuel Filter
Part Number:
FF679
---
The Fuel Filter is located: Under vehicle, passenger side, below seating area, passenger side of fuel tank, mounted on frame in fuel line

Oct 28, 2010 | Ford Taurus Cars & Trucks

1 Answer

I fixed used injection pump to engine and is not starting,i check oniy to fine out that the pump is not injecting fuel to the injectors.the timing is good.it is nissan navara 2000 model


1) There could be an air lock to the fuel system, try to bleed the system.
2) If the fuel is reaching the injector pump & not supplying to the injectors nozzles thn the pump needs attention.
Hope this helps!

Aug 18, 2010 | 1997 Nissan Pickup

2 Answers

I wanna change my fuel filter on my 2002 kia optima, can u tell me where its at.


If no external fuel filter is found in the fuel line, then there is a filter on each injector on the 4 cyl.

Fuel Injectors

WARNING
To avoid personal injury and/or vehicle damage, refer to the service precautions at the beginning of this section.
General Information Electronic fuel injectors for all gasoline engine applications are basically the same. They consist of an injector body, an electric solenoid, spring, nozzle and a filter. The injector is supplied a constant supply of pressurized fuel from the fuel system. The primary function of the fuel injector is to atomize gasoline into the surrounding air at the proper time. Throttle body injectors atomize fuel into the intake manifold or combustion chamber in much the same manner as a conventional carburetor (wet intake); port fuel injectors direct the atomized fuel at the back side of each cylinders intake valve(s) (dry intake). Gasoline direct injection systems operate at substantially higher pressure and direct the atomized fuel directly into the combustion chamber of each cylinder.

Jul 25, 2010 | 2002 Kia Optima

3 Answers

How do you check injectors on a 95 blazer 4.3 engine?


the injectors are under the upper intake plenum. they are not indavidual part but a plastic injector assembly the individual tubes to each cylinder are little poppet valves.this entire thing comes only as an assembly from a parts store or the dealer.yhe can not be tested individually.if only one cylinder is misfirring you may be able to attempt to clean it out with spray carb cleaner and reassemle to se if that worked.if it roccurs replace it.

Feb 16, 2010 | 1995 Chevrolet Blazer

1 Answer

How toreplace fuel injector chevy astro 1999


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure. Refer to the fuel system relief procedure in this section.
  3. Remove engine cover.
  4. Disconnect negative battery cable.
  5. Remove upper manifold assembly.
  6. Disconnect fuel meter body electrical connection and the fuel feed and return hoses from the engine fuel pipes.
  7. Remove poppet nozzle out of the casting socket by squeezing the nozzle locking tabs together.
  8. Remove fuel meter body by releasing the locktabs.
    NOTE Each injector is calibrated. When replacing the fuel injectors, be sure to replace it with the correct injector.
  9. Remove lower hold-down plate and nuts.
  10. While pulling the poppet nozzle tube downward, push with a small prytool down between the injector terminals and remove the injectors.

    0996b43f8022cb96.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the fuel meter assembly, including the injectors

To install:
  1. Lubricate the new injector O-ring seats with engine oil.
  2. Install o-rings on the injector.
  3. Install fuel injector into the fuel meter body injector socket.
  4. Install lower hold-down plate and nuts. Torque the nuts to 27 inch lbs. (3 Nm).
  5. Install fuel meter body assembly into the intake manifold. Torque the fuel meter bracket retainer bolts to 88 inch. lbs. (10 Nm).
    CAUTION To reduce the risk of fire or injury ensure that the poppet nozzles are properly seated and locked in their casting sockets.
  6. Install fuel meter body into the bracket and lock all the tabs in place.
  7. Install poppet nozzles into the casting sockets.
  8. Engage electrical connections.
  9. Install new o-ring seals on the fuel return and feed hoses.
  10. Connect fuel feed and return hoses and tighten the fuel pipe nuts to 22 ft. lbs. (30 Nm).
  11. Connect negative battery cable.
  12. Turn the ignition ON for 2 seconds and then turn it OFF for 10 seconds. Again turn the ignition ON and check for leaks.
  13. Install the engine cover.

Jan 20, 2010 | 1999 Chevrolet Astro

Not finding what you are looking for?
2000 Nissan Quest Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...