Question about Cars & Trucks

1 Answer

When i turn on my truck the belt on it squeeks goes away then churps a bit off and on. its a 2000 chevy truck.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 180 Answers

Matbe time for a belt,take it off and check all pulleys to make sure they spin free,but belts start to dry out and start to squeek an idler pulleys & reg pulleys

Posted on Dec 05, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

djicenova
  • 319 Answers

SOURCE: my belts squeak when i first start my truck up.

Replace the belts, if this doesnt solve, you have a slipping pulley.

Posted on Feb 27, 2009

  • 75 Answers

SOURCE: loud noise when I turn my truck on

This could posibly be the tensioner pulley. Oil the bearings and see if this helps.

Posted on Dec 08, 2009

Exhaustking
  • 43 Answers

SOURCE: put belt back on

there is a tensioner pulley that has a wrench fitting on it. if you look at one of the stickers under the hood there will be a diagram of which pulley it is. pry clockwise on the pulley after you have snaked the belt on the others. this will allow you to slide the belt onto the pulley.

Posted on Jan 02, 2010

  • 18 Answers

SOURCE: 2000 town & country van. serpintine belt slips

Sounds like the belt is worn out or the tenchiner pully is worn out so replace the belt and if it still does it then you will have to change the pully, but most of the time when this happens it is the belt so replace the belt and you should be good to go.

Posted on Mar 03, 2010

ourhowse
  • 2007 Answers

SOURCE: When engine starts from cold there is a squeeking

Try some belt dressing on the belt. You can get it at any parts store. If that doesn't help, replace the belt.

Posted on Jul 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 Chevy S10 rear end squeek that goes away when brakes are applied


If you have rear disc brakes, one of the rotors could be warped and causing the pads to move in the caliper.
You should be able to remove one wheel at a time, lock down the rotor with the lug nuts, and put the trans in low gear or reverse to listen for the noise.

Jan 14, 2013 | 1997 Chevrolet S-10 Pickup

1 Answer

SQUEEKING WHEN STARTING THAT GOES AWAY AFTER A COUPLE MINUTES


Loose or worn drive belts. Likely the one that drives the alternator and water pump. If you have more than 60k miles on your timing belt, have that done along with the belts. It is not cheap but less than a motor.

Feb 16, 2011 | 2000 Hyundai Elantra

1 Answer

I already replaced the belt, could it be defective if the squeeking is still there. 2000 rodeo 6cylinder tension pulley, can you adjust these


I am sure your new belt is fine.The tensioner will automaticaly adjust to the correct belt tension on its own.If You are convinced the squeeking is comming from the tensioner pully bearing then you need to replace it.Or you can do a quick check, by putting a wrench on it the same way you did to replace the belt.Pull and lift tensioner up and away from the belt and with your free hand spin the pully if it squssks or is rough to spin then it needs to be replaced, do this test with (Engine Not Running).Good Luck and have a good XMASS.

Dec 13, 2010 | 2000 Isuzu Rodeo

1 Answer

Churping sound upon start up between the firewall and engine. Sounds like a bearing but quites down some after engine running for a couple minutes.


I would try to remove the drive belt(s) and see if the chirping goes away, and also while the belt(s) are off, check that each rotatable pulley turns freely indicating that the bearings are ok.

Oct 28, 2010 | 2003 Lexus ES 300

1 Answer

When engine starts from cold there is a squeeking noise from the drive belt which goes away when the engine warms up its a 2004 sp23 with 40000 kms


Try some belt dressing on the belt. You can get it at any parts store. If that doesn't help, replace the belt.

Jul 03, 2010 | Cars & Trucks

2 Answers

2000 model chevy 3500 5.7 350


try changing the belt it might be squeeking it self or you did not replace the right part that was squeeking or another part was squeeking alnog with the idler

Jan 06, 2010 | 2000 Chevrolet Silverado

1 Answer

Engine squeek


Check your idler pulley(s) & serp. belt, alternator & lastly your timing belt idler. Squeeks generally signal impending bearing failure. With the engine running, turn on your lights: if it goes away or gets worse, most likely its the alternator. If it stays, could be the serp. idler. Using a long screwdriver, press the tip against the alternator frame and idler support and press your ear to the other end. Its crude, but it does work...should be able to get closer to the source. If you need to replace parts, start with the idler & serp. belt, then alternator (you might be able to have it rebuilt for a fraction of the cost) and lastly timing belt & idler.
Good luck.

Nov 10, 2009 | Cars & Trucks

1 Answer

Just a click away, NOT!


Starter solenoid most likely. Check the connections on the solenoid and the starter itself.

Sep 12, 2009 | 2000 Dodge Grand Caravan

2 Answers

Squillinng when turning


Squeeking sound when turning wheel and sitting there . Sounds like you could have a bad belt you can spray it with belt dressing spray and if the noise goes away you should replace belt .

Dec 01, 2008 | 1997 Ford Thunderbird LX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...