Question about 1993 Oldsmobile Cutlass Ciera

Open Question

Ignition relay 1993 ciera 3300

Where is it located no spark to coils

Posted by on

5 Suggested Answers

  • 1 Answer

SOURCE: STARTER - 1993 cutlass ciera

According to Chilton's, and assuming you have the 3300 V-6, it won't be fun. The first instruction is to drain the air conditioning system, and remove the front manifold. The starter is between the engine and the radiator. The deal breaker for me is the A/C draining/refill. If anyone knows of a way to avoid the A/C drain, let me know. Otherwise, I may just preemptively replace mine before my buddy runs low on R-12.

Posted on Nov 13, 2008

  • 337 Answers

SOURCE: where is the starter ignition

Front seating area, driver side, driver side of steering column, behind upper dash panel, mounted above fuse block

Posted on Dec 19, 2008

c17hydro
  • 2984 Answers

SOURCE: 1993 Oldsmobile Cutlass Ciera S 6 Cyl 3300 Speed Problem

Yep...try replacing your coil pack....

Posted on Mar 10, 2009

  • 158 Answers

SOURCE: ford telstar ignition coil f-694 and igniter deliver no spark

your distributor modual needs replacing

Posted on Apr 01, 2009

Mustgo
  • 2359 Answers

SOURCE: no spark on a 1996 vw jetta

With a volt meter,check for positive 12V on the coil.

post to body metal ground when the KEY is at on position.

===

Check alarm for ignition and/or start cut off.

Bad relay on alarm cut off (Bosch type relay)


Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a no starting problem I replaced the wires,plugs,coils,maf,ignition module,fuel filter,injectors,crank sensor,fuel pump relay,altenator,battery,oil pressure switch,Ecm


Are you getting power to the ignition module? It could be your ignition switch. I once had a 1993 Buick that would die intermittently with no rhyme or reason. Turned out to be the ignition switch. And my daughter has a 1995 Camaro that when you would start it...sometimes it would be a 2 cylinder, sometimes a 4 cylinder, and other times a 6. Still not sure how that one worked, but it was the ignition switch that is located on top of the steering column down by the firewall.

Jun 10, 2015 | 1989 Oldsmobile Cutlass Ciera

1 Answer

1991 Cutlass ceirra 3300 ,runs fine for short time. starts running rough,then dies/will not start again.changed fuel filter, then tested fuel pump.fuel pressure is good.what next ?


Check for spark when it won't start. If you have spark, might be your fuel pump relay, maybe the map sensor. If no spark, check another or all plug wires. If ignition isn't working, it could be Crankshaft Position sensor, Camshaft position sensor (or pick-up coil), ignition control module, coils, pcm, or the wiring associated with them. PCM determines spark timing after inputs from crank and can sensors, and sends ground signal to ignition module, cutting primary voltage to coils, initiating spark or high voltage from coil to sparkplug. All these parts have to be working right for ignition. All can be tested too. You'd need a digital volt ohm meter (DVOM) and a repair manual for your car with the test procedures. That Mitchell alldata-diy site has a special on subscriptions, pretty reasonable for a 1 month subscription, and excellent info and troubleshooting flow charts, wiring diagrams, etc.

Dec 26, 2012 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Where i the ignition module located ?


The ignition module is located under the coil packs on the v-6 engine.
That is where the spark plug wires go to the spark plugs . When you remove the coil packs ,the flat peice is themodule.When you remove the module , the crankshaft sensor is sometimes located there ,and that also should be changed

Feb 28, 2011 | 1996 Oldsmobile Cutlass Ciera

1 Answer

1989 oldsmobile ciera no spark unit cranks fine good fuel presure


most common cause of no spark is the ignition module located under the coil

Jan 09, 2010 | 1989 Oldsmobile Cutlass Ciera

2 Answers

Where is the cam sensor located on a 1994 olds cutlass cerias


with a 3.1 liter , remove and install directions are remove serpentine belt , remove power steering pump assembly , then remove sensor harness , sensor bolt , remove sensor , so it sounds like behind the power steering pump assembly area if that makes sense . it has to be real close the the cam gear , you should be able to find it .

Dec 29, 2008 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...