Question about 2005 Ford Freestyle

Open Question

Inner tie rod ford freestyle - 2005 Ford Freestyle

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
harley9701ha
  • 424 Answers

SOURCE: How to remove inner tie rods on a 95 Tracer/Escort wagon

You need a special tool that slides over the inner tie rod after removing the outer ones.make sure you count the turns to remove the outer tie rods so the alignment will be close. You will need to have it aligned after the repair.

Posted on Jan 29, 2009

Ad
  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

Murphybanton
  • 2004 Answers

SOURCE: inner tie rod end on passenger side needs replaced

You will definately need an expert to handle this because it is in a tight compartment.

Good luck.

Posted on May 27, 2009

tneubauer
  • 437 Answers

SOURCE: I need a suspension diagram that shows the Inner tie rods.

The inner tie rods are screwed into ends of the steering rack assembly.

Look at this diagram. #6 is the rubber boots and #7 is the shaft from the inner tie rods.


http://www.anubiscycle.com/fixya/2000-windstar-steering-gear.jpg

Posted on Jun 08, 2009

co7196
  • 3433 Answers

SOURCE: 1995 Ford Crown Victoria - shakes/vibrates @ highway speeds.

Alignment has alot to do with the tires not shimmying.. Like zero toe setting. Loose componants like tie rod ends and the idler ar worn. You can ck for excess front end play by holding the front and back of the wheel and pushing and pulling on it, like rocking it. OR have someone rock the steering while you watch where the play is from underneath. By rocking I mean turn the steering wheel back and forth. Look at all th joints and pivot points for excess play, which is, movement not immediate to the rest of the steering system. Tire balance is very important. Wheel hop is a sign of a bad tire and it overtaxes the shock absorber. Shocks don't cause shimmy because they are a vertical movement controlA shimmy is lateral or side to side.Wheel balance weights must be spit. If a 2 oz. weight is needed to balance the tire, Oe once should be on the inside of the wheel and one ounce on the outside directly across from each outher.. Loose wheel brgs will cause shimmy, but they would not last long. Caster setting on the wheel alignment will also cause shimmy. Like on a shopping car. too much caster causes the wheel to start fluttering and is very hard on other componants. This may be why you have worn tie rod ends and a bad pitman arm. Worn control arm bushings and ball joints directly affect titre wear and can only be feltwhen the front end hits a dip and detected by side wear on the tire edges. Summary: replace the tie rod end and have the car aligned. Good Luck, -Ned_ sorry about the book

Posted on Sep 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While breaking free the backing nut that holds the outer tie rod in place for alignment. The inner tie rod spins rotates as well. Is this normal? . 2007 Ford Edge or is inner shot as well?


This is normal. When replacing tie rods it is best to replace inner and outer at the same time. Be sure to mark the threads before disassembling. This will help to get the alignment close as possible then take it to a good alignment shop

Oct 25, 2016 | Ford Cars & Trucks

1 Answer

2002 FORD TAURUS INNER TIE ROD END


They screw on & then are cripped with a special tool

Dec 24, 2012 | 2002 Ford Taurus

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

3 Answers

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set...


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the whole process is installing the new ones to the exact settings of the old ones

Mar 13, 2010 | 1994 Ford Mustang

1 Answer

I need a suspension diagram that shows the Inner tie rods.


The inner tie rods are screwed into ends of the steering rack assembly.

Look at this diagram. #6 is the rubber boots and #7 is the shaft from the inner tie rods.


http://www.anubiscycle.com/fixya/2000-windstar-steering-gear.jpg

Jun 08, 2009 | 2000 Ford Windstar

2 Answers

Replacing tie rods


Maybe just a tie rod fork ...you can probably get a loaner free of charge (just requires a deposit) from Auto Zone or one of the chain parts stores.

Apr 01, 2009 | 1991 Mercury Sable

1 Answer

How to remove inner tie rods on a 95 Tracer/Escort wagon


You need a special tool that slides over the inner tie rod after removing the outer ones.make sure you count the turns to remove the outer tie rods so the alignment will be close. You will need to have it aligned after the repair.

Jan 29, 2009 | 1994 Ford Escort

1 Answer

Inner tie rods


Most of the time when you are not able to get inner tie rod ends it's because you would have to replace the rack and pinion assy. to take care of the inner tie rod issue.

Jun 09, 2008 | 1989 Ford Festiva

1 Answer

Inner tie rods


you can rent the tools for free when you buy the tie rods from autozone, o'reilly's etc. tool loosens tie rod.

Jun 05, 2008 | 1989 Ford Taurus

Not finding what you are looking for?
2005 Ford Freestyle Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...