Question about 2005 Hyundai Matrix 1.6

Open Question

Hyundai matrix1.6 twin cam marking for chain

Twin cam chain mark

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: timing belt have be removed before mark

maybe u can try use an sharp object like srew driver scrath around the cam body..coz it maybe hidden with some dirt..but if like my eg8,i will put a mark b4 put off evrything especially the timing belt..

Posted on Aug 08, 2008

  • 23 Answers

SOURCE: timing marks 2002 sonata 4 cyl twin cam balance shaft marks

look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Posted on Dec 24, 2008

  • 740 Answers

SOURCE: timimg marks on a 2004 hyundai sonata 2.4 dohc

Here is a diagram of you timing marks good luck and thanks for using FIX YA . please leave me a feedback.http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Mar 29, 2009

  • 12 Answers

SOURCE: Correct way to align timing marks

hi -- the timing marks on a twin cam are tricky!! heres how- turn the motor over to tdc on the bottom pulley,this will align two marks on the lower cog-----now on the top cog,it has an obvious mark near the teeth-- well disregard this for now!! the cog has a hole in it,in one of the spokes,well this goes at 12 o,clock and lines up with a mark you will see on the housing! now if you are right you will see the mark near the teeth is at around 4,oclock---i just did one and it is right--cheers

Posted on May 28, 2009

  • 510 Answers

SOURCE: Timing marks setting Hyundai Lantra

Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install timing chain with timing marks both crankshaft and camshaft


Hellen, For the second time, Re POST year, make, model, engine size and complete question so we, here at fixya can answer your question effectively.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Still pulling hair Twin Cam timing marks How accurate Engine Exhaust...
16v fast tbelt swap
Twin cam 16 valve timing marks Google Search

Aug 11, 2016 | Cars & Trucks

1 Answer

Timing marks on cam for timing chain 2007 Hyundai accent


right it a twin cam engine
the cam chain between the two cams
depends what cams are there
do these help

c848a2c4-69e8-4591-aab0-82d2fe2017f6.jpg26198503-log1nphqw4nlzn44ynu5rx0s-1-2.jpg

May 18, 2016 | 2007 Hyundai Accent 1.6

1 Answer

How do i set timing chain on sprockets ,ie top dead centre.


I don't know what car you have, so here's what was needed on mine:
1. Bring engine to Top Dead Center, ready to fire #1. There should be a mark on the front pulley or on the flywheel. Move cams to the TDC mark, too. My car was twin cam, the front cams needed to face apart, and set the marks....

Yours may be different.

May 12, 2015 | Cars & Trucks

1 Answer

How to line up timing chain marks on 2002 town and country 3.8 eng.


So I'm assuming it's twin cam so each cam has a mark on the sprockets line them up to a mark on the top of the valve covers and the crank goes straight up if the oil pump is being run by the belt it also has its on marks don't worry about the water pump

Aug 30, 2014 | Chrysler Town & Country Cars & Trucks

1 Answer

Timing chain marks needed for Audi A4 B9 1.8tfsi 2009 model. Engine was taken out and settings not marked. This is extremelyurgent. Please help


diagrams I have show a twin cam set up with 2 balancing shafts. The marks on the cam shaft point to (left cam shaft 11 oclock the mark on the right point to the 1 oclock position. The chain will have 3 black links-- the top black links will be at the timing marks on the shafts with the 3rd black link directly at 6 oclock facing a mark on the gear. The balancer marks both point to the 1 oclock position with black links on each and the 3rd black link will be facing a mark to the 7 oclock position on the crankahaft gear. Everything is done with the piston at TDC no 1 cylinder so get it there before you put the cam shafts in position or you will bend valves. Crank shaft gear is not keyed to the crank shaft. there are dots on the right hand balancer shaft gears and these dots will be as the 2 dots on adjacent teeth either side of a dot on the meshing gear. I suppose that is all as clear as mud but if you got this far then you will see the marks and marked links on the chains

Dec 22, 2013 | Cars & Trucks

1 Answer

I have 1998 hyundai excel twin cam l have just put cams out of 1999 excel and it sound like it has a lumpy cam now at lidle.Now my car smells like unburnt fuel.can this be from cam not being in right at...


double check all youre timing marks . loosten tentioner and adjust cam.then tighten chain .manually turn motor over twice then check timing marks again this is a little tricky sometimes because when you tighten the tentioner the cam will move. you have to have the chain in a spot to compensate for this movement.

Dec 02, 2013 | Cars & Trucks

1 Answer

Hey guys I need to get changed the timming belt on my hyundai accent 1995 and I can do it myself but don´t have the timming marks diagram, can you please help me?


if its a single cam the marks should be on the backing plate and if it is twin cam the two marks should face each other on the compression stroke of the number 1 cylinder and the same goes for single cams line the mark up with the backing plate in the compression stroke of number 1 cylinder.

May 27, 2010 | 2001 Hyundai Accent

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

1 Answer

Correct way to align timing marks


hi -- the timing marks on a twin cam are tricky!! heres how- turn the motor over to tdc on the bottom pulley,this will align two marks on the lower cog-----now on the top cog,it has an obvious mark near the teeth-- well disregard this for now!! the cog has a hole in it,in one of the spokes,well this goes at 12 o,clock and lines up with a mark you will see on the housing! now if you are right you will see the mark near the teeth is at around 4,oclock---i just did one and it is right--cheers

May 11, 2009 | 1994 Hyundai Excel

1 Answer

Timing marks 2002 sonata 4 cyl twin cam balance shaft marks


look for marks on the timeing gears there sould be a couple notches. then bring them center to center

Dec 24, 2008 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
2005 Hyundai Matrix 1.6 Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...