Question about 2007 Chevrolet Silverado 2500HD

Open Question

OBD II check engine light on, DTC P1825 and PO700 set

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1996 Chevy Blazer check engine light on

More then likely its the Canister Purge Solenoid. you can find it online at www.autozone.com the part number is PV140. And to replace it on blazer you have to remove the spare tire. Alot of people don't know where this part is so I hope this helps you and good luck.

Posted on Oct 14, 2008

Ad
  • 56 Answers

SOURCE: my check engine light is on & the dtc is p0171 2005 chevy impala

I found this On-Line

Causes A code P0171 may mean that one or more of the following has happened:

  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor.
Possible Solutions Possible solutions include:
  • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
  • Inspect all vacuum and PCV hoses, replace if necessary
  • Check for a dirty fuel filter and proper fuel pressure2_bing.gif

Posted on Jun 12, 2010

SOURCE: where to plug in dioagnostic reader 98 chevy prizm

Your spark plugs are damaged

Is that not a no brainer?

Timing belt & you may have major damage
to valves,pistons etc

Need to get a camera inside cylinder to inspect
& then do a cylinder leak down test

Posted on Oct 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTC P0700?


Please go to this site on pc, to read all about po700. www.obd-codes.com/po700 God-Bless! When page comes up, click on the 4th link down. It will give detailed info on this code.

Feb 23, 2016 | Cars & Trucks

Tip

Obd-ii error codes


OBD-II (Check Engine Light) Trouble Codes Welcome to OBD-Codes.com, your headquarters for everything OBD-II related. For more information on what OBD codes are, OBD-II codes explained, explanation of fuel trims, or answers to other questions, visit our FAQ area. The most common OBD-II codes are P0xxx powertrain codes, which are listed below on this page, along with P2xxx generic & P3xxx generic codes (please scroll down). For the other OBD-II codes, choose from Bxxxx - B Codes - OBD-II Body Codes or Cxxxx - C Codes - Chassis Codes, and Uxxxx - U - Network Codes. If your DTC (diagnostic trouble code) begins with P1xxx, that means it's a manufacturer specific code. For more information on P1 codes, choose your vehicle make here: Acura Audi BMW Chevrolet Dodge / Chrysler / Jeep Ford Honda Hyundai Infiniti Isuzu Jaguar Kia Land Rover Lexus Mazda Mitsubishi Nissan Subaru Toyota VW

Please use our new & improved search engine to find information on your trouble codes. Search Now! This list contains standard diagnostic trouble codes (DTC's) that are used by some manufacturers to identify vehicle problems. The codes provide below are generic codes that may not apply to all vehicles. Vehicle manufacturers may use manufacturer specific DTC codes that are different from the codes shown below. Foreign vehicles may also use DTC codes different from the generic DTC codes. We recommend that you not depend on the DTC codes in this list for vehicle repairs until you confirm the generic DTC codes apply to your vehicle(s). The list below is for information purposes only and is not intended for use in vehicle repairs.

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

on Apr 14, 2015 | Cars & Trucks

2 Answers

What are the probable causes of DTC P0720?


According to the database the code means OUTPUT SPEED SENSOR CIRCUT MALFUNCTION.

Dec 12, 2015 | Cars & Trucks

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

Chrysler P0560 code


Generic OBD Error Code Details for P0560 System Voltage OBD II Code P0560 refers to
The battery supplies electricity to the ECM even when the ignition switch is OFF. This electricity allows the ECM to store data such as DTC history, freeze frame data, fuel trim values and other data. If the battery voltage falls below a minimum level, the ECM will conclude that there is a fault in the power supply circuit. The next time the engine starts, the ECM will turn on the MIL and a DTC will be set. SymptomsPossible sumptoms of OBD code P0560
- Engine Light ON (or Service Engine Soon Warning Light) - Slow engine start - Low battery power CausesPossible causes of OBD code P0560
- Loose or missing alternator drive belt - Faulty alternator - Battery defective - Open or short system voltage circuit The Error code is generally activated on detection of the following conditions: The P0560 code is detected when there is an open in ECM back-up power source circuit

Apr 24, 2012 | 2002 Chrysler 300M

1 Answer

Mecedes ml320 dies if i let off the gas


Vehicles: All post-1996 (OBD-II) vehicles experiencing the above symptoms

Check your IAC Valve (Idle Air Control Valve), and TPS (Throttle Position Sensor), and throttle linkage.
You could even be having problems on the spark side of the equation - the ICM (Ignition Control Module), spark plugs, coil pack(s), etc.
On the fuel side, you may have an underperforming fuel pump (leading to low fuel pressure), or bad fuel pressure regulator, or even clogged fuel filter/fuel strainer.

You'll want to query your car's computer to find what OBD-II DTC (Diagnostic Trouble Code) that the car's computer has stored. The presence of this stored DTC code is the reason that your Mercedes has lit the CEL (Check Engine Light).

One can get a free DTC code check (in the US) at AutoZone/Advance Auto Parts/Pep Boys. When you have this code (they may look up a brief explaination of the code for you), you'll at least have a good indication of which engine system has been found by your car's ECC (Engine Control Computer) to be performing erroneously.
OBD-II = On-Board Diagnostics II (applies to 1996 and newer model years)

Dec 04, 2011 | Cars & Trucks

2 Answers

How to change a throttle position sensor on a 94 ford f150 5.0 4x4


How to Replace a Throttle Position Sensor
(DIY & Save up to $135.75 ) - Time: 2.1 hours

Parts:
1. Throttle Position Sensor - $ 55.44

Tools:
1. Scan Tool
2. Screwdriver
3. Multimeter

Procedure:
1. Locate the OBD data link connector (DLC). Refer to your owner’s manual for the specific location.
  • Tip: The OBD-I data link connector is usually located in the engine compartment near the battery or the fuse box. The OBD-II connector (post 1995 cars) is usually located beneath the instument panel next to the steering column.
2. Turn your key to the“ON” position. Do not start the engine.

3. Plug your scan tool into the OBD data link connector. Turn on the scan tool and select the appropriate steps to read the diagnostic trouble code (DTC).

    6db8845.jpg

Scanner plugged into OBD-II data link connector.
  • Tip: The OBD-II diagnostic trouble code (DTC) is a 5 character alphanumeric code. The first digit is a letter that indicates the component group, the second digit is OBD mandated or manufacturer specfic, the third digit is a subgroup, and the fourth and fifth digits define the component and basic problem.
  • 4. Locate the throttle position sensor.
6182d26.jpg

  • Throttle position sensor

  • 5. Disconnect the electrical connector from the throttle position sensor.
fc565b1.jpg

  • Electrical connector removed
6. Test the resistance of the throttle position sensor (TPS) with a digital multi-meter. If the resistance is out of specifications, the TPS must be replaced.
  • 7. Remove the throttle position sensor.

  • d3a8007.jpg

    Removing sensor mounting screws

    8. Install the new throttle position sensor. Tighten the mounting screws and attach the electrical connector.
  • 9. Erase the diagnostic trouble code (DTC) with the scan tool using the“delete” or“erase” command. Road test your vehicle to see if the check engine light returns.
fde01cf.jpg

    Check engine light

  • Tip: If the check engine light returns, repeat the diagnostic process for additional DTCs or take your vehicle to a certified repair shop.
Direct OE replacement

Hope helped with this. Good luck (remember rated this help).

Nov 05, 2009 | Ford F-150 Cars & Trucks

1 Answer

Tranny stuck in low gear


have you check your fluid level?

Jun 26, 2009 | 1997 Dodge Grand Caravan

2 Answers

2002 Chevy Trailblazer w/101,000 mi has the P0440 OBD II Code. Just replaced the plugs with Iridiums @ 100K, all connections are good and gas cap is seated properly . . . help!!!


i have 2003 trailblazer ltz 153 000 mileage i have code po440 .i changed gas cap and turned off the chech engine light... i made 300 miles and it was good and today morning i drove a mile and light turned on ..... what do i have to fix ...thanks

Mar 22, 2009 | 2003 Chevrolet TrailBlazer

Not finding what you are looking for?
2007 Chevrolet Silverado 2500HD Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...