Question about Mini Cooper S

1 Answer

My touch screen is not working I replaced a touchpad but still the problem persist

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Contact Service provider first.

Posted on Dec 05, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The touch screen in my Highlander is not working. The radio seems sort of ok but my map, bluetooth set up is not responding

You will need to remove the touch screen module and have it repaired or replace it, they run about $5000.00

Sep 23, 2016 | Toyota Highlander Cars & Trucks

1 Answer

2004 Lexus GX470 touch screen is not working.

The owners manual should describe fuse locations in detail.

Apr 05, 2016 | 2004 Lexus GX 470

1 Answer

How fix Dodge Grand Caravan Touch Screen Not Working

Dodge Grand Caravan Touch Screen Not Working - YouTube

? 0:21
Jul 10, 2014 - Uploaded by Radionut R
The touchscreen of my 2008 Dodge grand Caravan quit working. ... Chrysler Town & Country - 3 Common ...

Dodge Grand Caravan nav touch screen not working ... - Fixya > ... > Cars & Trucks > Dodge
Dodge Grand Caravan cars & trucks nav touch screen not working questions and ... How do I fix this problem? check fuses first then check the bulbs do not touch ...

Dodge car touch screen not working Questions & Answers ...

Dec 14, 2015 | Dodge Cars & Trucks

1 Answer

Putting the car into reverse and giving it gas makes the fuel injector coil and fuse blow. Whats the problem?

Look at injectors harness .When put in reverse engine move toward firewall then wire could touch the ground
hope it help

Dec 31, 2014 | 1996 Oldsmobile Cutlass Ciera

1 Answer

Stalls at 1/2 tank

check if your fuel system runs off of vacuum if you have break any where

Sep 06, 2012 | Saturn L-Series Cars & Trucks

2 Answers

2009 Jeep Wranger Navigation Radio Touch Screen

look into a radio repair shop or just get a after market radio installed at a audio store best buy-etc

Aug 22, 2012 | Jeep Wrangler Cars & Trucks

1 Answer

My lexus IS 300 model 2007 the touch screen is not working when i press on "I agree" button it is not working all the touch buttons are not working i have tried replace the battery after this...

dear did you found any solution. because i have also IS300 2008 and everything was working fine but after cleaning the car in cleaning station (full cleaning with polish for exterior and interior) now touch screen not working at all, only side buttons, sometimes when i press the side navigation button and i touch the screen it will move the map only down but for climate and other setting no response at all..

need your help pleaseeeeeeeeeeeee

Nov 25, 2010 | 2007 Lexus GS300

1 Answer

91 bmw 325I

Hi there. It sounds like the car has a short between the II and I position. Something like the ACC and START positions in domestic and imports. And it all happened when replacing the starter. These wires are touching chassis, or ground. Try removing and emplace it again, making sure the wires are not touching GND. If problem persists, then the problem might be in the switch, ergo, requiring further inspection of the electrical system, including the wiring. Also check the fuses and make sure they are not blown. If replaced and still blowing, is a critical shortage, and the risk of an electrical fire will become imminent. Let me know how things go. Good luck.

Aug 25, 2008 | 2001 BMW 325

4 Answers

Buick Redezvous

I had this same problem, I took the touchpad off by removing the two #15 torx screws from the outside of the car under the lift handle. Removed the wire clip which was very short. The touch pad comes apart. It is held together with six phillips screws. Its a pretty simple switch. I cleaned the copper contacts with copper a vinegar and salt solution. Heated the solution in the microwave and then soaked the contact plate. I also found corrosion on the terminal. Did a little soldering to fix it, put it all back together and it works fine. Hope this helps. :)

Jun 23, 2008 | 2004 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mini Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

77202 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8755 Answers

Are you a Mini Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides